Nissan Teana J32. Manual — part 600
EXT-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000003733752
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes clips, pawls and metal clips
SIIA0995E
PIIB7923J
FRONT BUMPER
EXT-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ON-VEHICLE REPAIR
FRONT BUMPER
Exploded View
INFOID:0000000003819529
1.
Bumper side bracket RH
2.
Bumper stay RH
3.
Bumper reinforcement
4.
Grommet RH
5.
Bumper fascia assembly
6.
Bumper molding RH
7.
Headlamp washer nozzle cover RH
8.
Licence plate bracket
9.
Spring nut
10. Headlamp washer nozzle cover LH
11.
Bumper molding LH
12. Grommet LH
13. Bumper energy absorber
14.
Bumper side bracket LH
15. Bumper stay LH
JMKIA2516ZZ
EXT-12
< ON-VEHICLE REPAIR >
FRONT BUMPER
Removal and Installation
INFOID:0000000003819530
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open hood assembly.
2.
Remove clips (A) of front bumper fascia upper side.
3.
Remove front bumper fascia fixing screws (A) and clips (B) from
front bumper fascia lower side.
4.
Disconnect front fog lamp harness connectors (LH/RH).
5.
Disconnect headlamp washer tube connector. Refer to
WW-97, "Removal and Installation"
6.
Remove fender protector fixing clips to access front bumper fas-
cia fixing screw (A), and then remove front bumper fascia fixing
screws (LH/RH).
16. Front fog lamp bracket RH
17.
Front fog lamp bracket LH
18. Front fog lamp LH
19. Bumper upper retainer
20.
Front fog lamp RH
JMKIA2517ZZ
JMKIA2518ZZ
JMKIA2519ZZ
FRONT BUMPER
EXT-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
7.
Pull bumper fascia side toward the vehicle side to disengage the
bumper fascia from bumper side brackets (LH/RH).
8.
Disengage front bumper fascia from bumper brackets (A) (LH/
RH).
9.
Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
10. Remove the following parts after removing bumper fascia.
• License plate bracket
• Front bumper retainer
• Front bumper molding (LH/RH)
• Headlamp washer nozzle (LH/RH). Refer to
WW-102, "Removal and Installation"
.
• Front fog lamps (LH/RH). Refer to
EXL-183, "Removal and Installation"
.
11. Remove bumper energy absorber.
12. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement with power tool.
13. Remove bumper stay (LH/RH) mounting bolts, and then remove bumper stay (LH/RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing, perform fitting adjustment.
: Pawl
JMKIA2520ZZ
JMKIA2521ZZ
JMKIA2550ZZ
Portion
Clearance
Flush
Front bumper – Front grille
A – A 3.5 – 8.5 mm (0.138 – 0.335 in)
—
Front bumper – Hood
B – B 3.7 – 8.3 mm (0.146 – 0.327 in)
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст