Nissan Teana J32. Manual — part 601
EXT-14
< ON-VEHICLE REPAIR >
FRONT BUMPER
Front bumper – Headlamp
C – C 0.5 – 2.5 mm (0.020 – 0.098 in)
—
Front bumper – Front fender D – D 0.0 – 0.7 mm (0.000 – 0.028 in)
−
0.3 – 1.7 mm (
−
0.012 – 0.067 in)
Portion
Clearance
Flush
REAR BUMPER
EXT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REAR BUMPER
Exploded View
INFOID:0000000003819531
1.
Bumper side bracket LH
2.
Grommet LH
3.
Bumper molding LH
4.
Rear fog lamp rim
5.
Bumper molding RH
6.
Bumper energy absorber
7.
Bumper side bracket RH
8.
Bumper stay RH
9.
Bumper stay LH
JMKIA2522ZZ
EXT-16
< ON-VEHICLE REPAIR >
REAR BUMPER
Removal and Installation
INFOID:0000000003819532
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open trunk lid assembly.
2.
Remove rear combination lamp (LH/RH). Refer to
EXL-191, "Removal and Installation"
3.
Remove clips (A) and screws (B) located under rear combina-
tion lamp (LH/RH).
4.
Remove screws (A) of bumper fascia underside.
5.
Remove rear wheel house protector fixing clips (A) (LH/RH) and
remove rear bumper fascia fixing screws (B) (LH/RH).
10. Rear fog lamp
11.
Rear bumper fascia assembly
12. Grommet RH
13. Bumper reinforcement
: Pawl
JMKIA2523ZZ
JMKIA2524ZZ
JMKIA2525ZZ
REAR BUMPER
EXT-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
6.
Pull rear bumper fascia side toward the vehicle side to disen-
gage the rear bumper fascia from bumper side bracket (LH/RH).
7.
Disconnect rear fog lamp (1) harness connector (A).
8.
Pull out bumper fascia toward rear of vehicle.
9.
Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
10. Remove the following parts after removing bumper fascia.
• Rear fog lamp. Refer to
EXL-194, "Removal and Installation"
• Rear bumper molding (LH/RH).
11. Remove bumper energy absorber.
12. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement with power tool.
13. Remove rear bumper stay (LH/RH) mounting bolts, and then remove rear bumper stay (LH/RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing, perform fitting adjustment.
: Pawl
JMKIA2526ZZ
JMKIA2527ZZ
JMKIA2551ZZ
Portion
Clearance
Flush
Rear bumper – Rear fender A – A 0.0 – 0.8 mm (0.000 – 0.031 in)
−
0.2 – 1.8 mm (
−
0.008 – 0.071 in)
Rear bumper – Rear com-
bination lamp
B – B 0.5 – 3.5 mm (0.020 – 0.138 in)
—
Rear bumper – Trunk lid
C – C 5.0 – 9.0 mm (0.197 – 0.354 in)
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст