Nissan Teana J32. Manual — part 971
HEATED SEAT SWITCH
SE-17
< COMPONENT DIAGNOSIS >
[WITH VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace rear ventilation seat control unit. Refer to
SE-100, "Disassembly and Assembly"
6.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
REAR SEAT : Component Inspection
INFOID:0000000003847097
1.
CHECK HEATED SEAT SWITCH
1.
Turn ignition OFF.
2.
Disconnect rear heated seat switch connector.
3.
Check rear heated seat switch terminals.
Is the inspection result normal?
YES
>> Rear heated seat switch is OK.
NO
>> Replace rear heated seat switch. Refer to
SE-105, "REAR SEAT : Removal and Installation"
.
(+)
(–)
Voltage (V)
(Approx.)
Rear ventilation seat control unit
Connector
Terminal
LH
LO
B490
52
Ground
Battery voltage
HI
51
RH
LO
B501
52
HI
51
Rear heated seat switch
Terminal
Condition
Continuity
LH
B494
2
3
Rear heated seat switch
LO mode
Pressed
Existed
Released
Not existed
1
HI mode
Pressed
Existed
Released
Not existed
RH
B505
2
3
Rear heated seat switch
LO mode
Pressed
Existed
Released
Not existed
1
HI mode
Pressed
Existed
Released
Not existed
SE-18
< COMPONENT DIAGNOSIS >
[WITH VENTILATION SEAT]
VENTILATION SEAT SWITCH
VENTILATION SEAT SWITCH
FRONT SEAT
FRONT SEAT : Description
INFOID:0000000003825956
Switches the LO or HI air flow of the front ventilation seat and turns OFF the front ventilation seat operation.
FRONT SEAT : Component Function Check
INFOID:0000000003825957
1.
CHECK FUNCTION
Check that the related indicator lamp illuminates when front ventilation seat switch is set to LO or HI position.
Is the inspection result normal?
YES
>> Front ventilation seat switch function is OK.
NO
>> Refer to
SE-18, "FRONT SEAT : Diagnosis Procedure"
FRONT SEAT : Diagnosis Procedure
INFOID:0000000003847164
1.
CHECK FRONT VENTILATION SEAT CONTROL UNIT INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between front ventilation seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> Front ventilation seat switch circuit is OK.
NO-1
>> LO or HI mode is NG: GO TO 2.
NO-2
>> LO and HI modes are NG: GO TO 3.
2.
CHECK FRONT VENTILATION SEAT SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front ventilation seat switch connector and front ventilation seat control unit connector.
3.
Check continuity between front ventilation seat switch harness connector and front ventilation seat control
unit harness connector.
4.
Check continuity between front ventilation seat switch harness connector and ground.
(+)
(–)
Condition
Voltage (V)
(Approx.)
Front ventilation seat control unit
Connector
Terminal
Driver side
B466
48
Ground
Front ventilation seat switch
LO mode
Pressed
0
Released
Battery voltage
47
HI mode
Pressed
0
Released
Battery voltage
Passenger side
B442
48
Front ventilation seat switch
LO mode
Pressed
0
Released
Battery voltage
47
HI mode
Pressed
0
Released
Battery voltage
Front ventilation seat switch
Front ventilation seat control unit
Continuity
Connector
Terminal
Connector
Terminal
Driver side
LO
M208
2
B446
48
Existed
HI
1
47
Passenger side
LO
M209
2
B442
48
HI
1
47
VENTILATION SEAT SWITCH
SE-19
< COMPONENT DIAGNOSIS >
[WITH VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FRONT VENTILATION SEAT SWITCH
Check front ventilation seat switch.
Refer to
SE-20, "FRONT SEAT : Component Inspection"
.
Is the inspection result normal?
YES-1 >> LO or HI mode is NG: GO TO 5.
YES-2 >> LO and HI modes are NG: GO TO 4.
NO
>> Replace front ventilation seat switch. Refer to
SE-106, "FRONT SEAT : Removal and Installation"
.
4.
CHECK FRONT VENTILATION SEAT SWITCH GROUND CIRCUIT
Check continuity front ventilation seat switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
5.
CHECK FRONT VENTILATION SEAT CONTROL UNIT OUTPUT SIGNAL
1.
Connect front ventilation seat control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between front ventilation seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace front ventilation seat control unit. Refer to
SE-93, "Disassembly and Assembly"
.
6.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
Front ventilation seat switch
Ground
Continuity
Connector
Terminal
Driver side
LO
M208
2
Not existed
HI
1
Passenger side
LO
M209
2
HI
1
Front ventilation seat switch
Ground
Continuity
Connector
Terminal
Driver side
M208
3
Existed
Passenger side
M209
(+)
(–)
Voltage (V)
(Approx.)
Front ventilation seat control unit
Connector
Terminal
Driver side
LO
B466
48
Ground
Battery voltage
HI
47
Passenger side
LO
B442
48
HI
47
SE-20
< COMPONENT DIAGNOSIS >
[WITH VENTILATION SEAT]
VENTILATION SEAT SWITCH
FRONT SEAT : Component Inspection
INFOID:0000000003847165
1.
CHECK FRONT VENTILATION SEAT SWITCH
1.
Turn ignition OFF.
2.
Disconnect front ventilation seat switch connector.
3.
Check front ventilation seat switch terminals.
Is the inspection result normal?
YES
>> Front ventilation seat switch is OK.
NO
>> Replace front ventilation seat switch. Refer to
SE-106, "FRONT SEAT : Removal and Installation"
.
REAR SEAT
REAR SEAT : Description
INFOID:0000000003843435
Switches the LO or HI air flow of the rear ventilation seat and turns OFF the rear ventilation seat operation.
REAR SEAT : Component Function Check
INFOID:0000000003843436
1.
CHECK FUNCTION
Check that the related indicator lamp illuminates when rear ventilation seat switch is set to LO or HI position.
Is the inspection result normal?
YES
>> Rear ventilation seat switch function is OK.
NO
>> Refer to
SE-20, "REAR SEAT : Diagnosis Procedure"
.
REAR SEAT : Diagnosis Procedure
INFOID:0000000003847166
1.
CHECK REAR VENTILATION SEAT CONTROL UNIT INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between rear ventilation seat control unit harness connector and ground.
Is the inspection result normal?
Front ventilation seat switch
Terminal
Condition
Continuity
Driver side
M208
2
3
Front ventilation seat switch
LO mode
Pressed
Existed
Released
Not existed
1
HI mode
Pressed
Existed
Released
Not existed
Passenger side
M209
2
3
Front ventilation seat switch
LO mode
Pressed
Existed
Released
Not existed
1
HI mode
Pressed
Existed
Released
Not existed
(+)
(–)
Condition
Voltage (V)
(Approx.)
Rear ventilation seat control unit
Connector
Terminal
LH
B490
48
Ground
Rear ventilation seat switch
LO mode
Pressed
0
Released
Battery voltage
47
HI mode
Pressed
0
Released
Battery voltage
RH
B501
48
Rear ventilation seat switch
LO mode
Pressed
0
Released
Battery voltage
47
HI mode
Pressed
0
Released
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст