Nissan Teana J32. Manual — part 933
RAX-4
< ON-VEHICLE REPAIR >
REAR WHEEL HUB AND HOUSING
ON-VEHICLE REPAIR
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000003811099
Removal and Installation
INFOID:0000000003811100
REMOVAL
1.
Remove tire.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-58, "REAR WHEEL SENSOR : Exploded View"
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-40, "BRAKE CALIPER ASSEMBLY : Exploded View"
4.
Remove disc rotor. Refer to
BR-41, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
5.
Remove cotter pin, then loosen suspension arm mounting nut of axle housing. Refer to
.
6.
Remove wheel hub and bearing assembly.
7.
Remove parking brake shoe and parking brake cable from back plate. Refer to
and
8.
Remove anchor block mounting nuts, and then remove anchor block and back plate from axle housing.
9.
Remove stabilizer connecting rod (upper side). Refer to
.
10. Remove radius rod (axle housing side). Refer to
11. Remove coil spring. Refer to
12. Set suitable jack under axle housing.
13. Remove shock absorber (lower side). Refer to
14. Remove front lower link (axle housing side). Refer to
.
15. Separate suspension arm from axle housing so as not to damage ball joint boot using ball joint remover,
and then remove axle housing from the vehicle.
CAUTION:
1.
Hub cap
2.
Ball seat
3.
Bushing
4.
Cotter pin
5.
Axle housing
6.
Back plate
7.
Anchor block
8.
Wheel hub and bearing assembly
Refer to
for symbols in the figure.
JPDIG0104GB
REAR WHEEL HUB AND HOUSING
RAX-5
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
Temporarily tighten nuts to prevent damage to threads and to prevent the ball joint remover from
coming off.
16. Remove hub cap.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and steering knuckle.
• Never reuse cotter pin.
Inspection
INFOID:0000000003811101
INSPECTION AFTER REMOVAL
Wheel Hub and Bearing Assembly
Check the wheel hub and bearing assembly for wear, cracks, and damage. Replace if necessary.
Axle Housing
Check the axle housing for wear, cracks, and damage. Replace if necessary.
Ball Joint Inspection
Check for boot breakage, axial looseness, and torque of suspension arm ball joint. Refer to
.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
(without VDC),
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
2.
Adjust parking brake operation (stroke). Refer to
PB-2, "Inspection and Adjustment"
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor (with VDC). Refer to
STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
RAX-6
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000003811102
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
RF-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
RF
A
B
RF
N
O
P
CONTENTS
ROOF
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
WorkFlow . . . . . . . . . . . . . . . . ..
INSPECTION AND ADJUSTMENT . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . ...
FUNCTION DIAGNOSIS . . . . . . . ...
SUNROOF SYSTEM . . . . . . . . . . ...
System Diagram . . . . . . . . . . . . . ...
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
RETAINED PWR . . . . . . . . . . . . . ...
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) . . . . . . . . . . . . ...
COMPONENT DIAGNOSIS . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT . ..
BCM . . . . . . . . . . . . . . . . . . ...
BCM : Diagnosis Procedure . . . . . . . . .
SUNROOF MOTOR ASSEMBLY . . . . . . . ..
SUNROOF MOTOR ASSEMBLY :
Diagnosis Procedure . . . . . . . . . . . ..
SUNSHADE MOTOR ASSEMBLY . . . . . . .
SUNSHADE MOTOR ASSEMBLY :
Diagnosis Procedure . . . . . . . . . . . ..
COMMUNICATION SIGNAL CIRCUIT . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
SUNROOF SWITCH . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . . .
DOOR SWITCH . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
ECU DIAGNOSIS . . . . . . . . . . .
BCM (BODY CONTROL MODULE) . . . . .
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram - BCM - . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ...
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ...
SUNROOF MOTOR ASSEMBLY . . . . . .
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram - SUNROOF CONTROL SYS-
TEM - . . . . . . . . . . . . . . . . . ...
SUNSHADE MOTOR ASSEMBLY . . . . ...
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram - SUNROOF CONTROL SYS-
TEM - . . . . . . . . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . ..
SUNROOF DOES NOT OPERATE PROPER-
LY . . . . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст