Nissan Teana J32. Manual — part 555
EXL-190
< ON-VEHICLE REPAIR >
[XENON TYPE]
AUTO LEVELIZER CONTROL UNIT
AUTO LEVELIZER CONTROL UNIT
Exploded View
INFOID:0000000003774377
Removal and Installation
INFOID:0000000003774378
Removal
1.
Remove the auto levelizer control unit bolt.
2.
Remove the sensor lever link bracket bolt.
3.
Disconnect the auto levelizer control unit connector.
4.
Remove the auto levelizer control unit.
Installation
Install in the reverse order of removal.
CAUTION:
• Be sure to perform sensor initialization if auto levelizer control unit is removed. Refer to
"SENSOR INITIALIZE : Special Repair Requirement (HEADLAMP AIMING CONTROL SYSTEM)"
• Be sure to perform “WRITE CONFIGURATION” with CONSULT-III when replacing the auto levelizer
EXL-9, "CONFIGURATION (HEADLAMP LEVELIZER) : Special Repair Require-
1.
Auto levelizer control unit
A.
Auto levelizer control unit bolt
B.
Sensor lever link bracket bolt
JPLIA1147ZZ
REAR COMBINATION LAMP
EXL-191
< ON-VEHICLE REPAIR >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000003773634
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003773635
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the rear combination lamp finisher.
2.
Remove the rear combination lamp mounting bolts.
3.
Pull the rear combination lamp toward outside of the vehicle. And then remove the rear combination lamp.
4.
Disconnect the rear combination lamp connector.
INSTALLATION
Install in the reverse order of removal.
1.
Rear combination lamp
2.
Rear combination lamp finisher
JPLIA1097ZZ
1.
Back-up lamp bulb
2.
Back-up lamp bulb socket
3.
Rear turn signal lamp bulb socket
4.
Rear turn signal lamp bulb
JPLIA1098ZZ
EXL-192
< ON-VEHICLE REPAIR >
[XENON TYPE]
REAR COMBINATION LAMP
Replacement
INFOID:0000000003773636
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement integral with rear combination lamp. Refer to
.
REAR TURN SIGNAL LAMP BULB
1.
Remove the rear combination lamp. Refer to
2.
Rotate the rear turn signal lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the rear turn signal lamp bulb socket.
BACK-UP LAMP BULB
1.
Remove the rear combination lamp. Refer to
2.
Rotate the back-up lamp bulb socket counterclockwise, and unlock it.
3.
Remove the bulb from the back-up lamp bulb socket.
HIGH-MOUNTED STOP LAMP
EXL-193
< ON-VEHICLE REPAIR >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000003773637
Removal and Installation
INFOID:0000000003773638
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the rear parcel shelf finisher. Refer to
2.
Remove the screw. And then disconnect the connector.
3.
Remove the high-mounted stop lamp.
INSTALLATION
Install in the reverse order of removal.
1.
High-mounted stop lamp
2.
Rear parcel shelf finisher
JPLIA1099ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст