Nissan Teana J32. Manual — part 753
INT-32
< ON-VEHICLE REPAIR >
FRONT DOOR FINISHER
7.
Disconnect lock knob cable (1), inside handle cable (2), power
window switch finisher harness connectors (B) and seat memory
switch harness connector (A).
8.
Remove front door finisher.
9.
Remove the following parts after removing front door finisher.
• Front door inside handle. Refer to
DLK-223, "INSIDE HANDLE : Removal and Installation"
.
• Seat memory switch. Refer to
ADP-137, "Removal and Installation"
.
• Disengage power window switch finisher (1) pawls as shown by the figure by pressing them toward the
arrow, then remove the power window switch finisher (1) from the door finisher (2).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
PASSENGER SIDE
JMJIA1761ZZ
JMJIA1954ZZ
FRONT DOOR FINISHER
INT-33
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PASSENGER SIDE : Exploded View
INFOID:0000000003819218
PASSENGER SIDE : Removal and Installation
INFOID:0000000003819219
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
REMOVAL
1.
Fully open door window.
1.
Front door panel
2.
Front door inside handle
3.
Front door finisher
4.
Cap
5.
Step lamp
6.
Front door grip
7.
Front door grip cover
8.
Inside handle escutcheon
9.
Power window switch finisher
10. Power window switch
: Clip
: Pawl
: Metal clip
JMJIA1799ZZ
INT-34
< ON-VEHICLE REPAIR >
FRONT DOOR FINISHER
2.
Remove inside handle escutcheon (1) with a flat-bladed screw-
driver (A) wrapped in a tape as shown in the figure.
3.
Remove screw (A) located on the back side of inside handle
escutcheon.
4.
Disengage the front door grip cover (1) and cap (2) fixing pawls
with a remover tool (A).
5.
Remove front door grip fixing bolt (A) with tool.
6.
Remove front door finisher fixing bolt with tool (A) as shown in
the figure.
: Pawl
JMJIA1756ZZ
JMJIA1758ZZ
: Pawl
JMJIA1763ZZ
JMJIA1765ZZ
JMJIA1767ZZ
FRONT DOOR FINISHER
INT-35
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
7.
Remove step lamp and then disconnect the harness connector. Refer to
INL-96, "Removal and Installa-
8.
Insert a remover tool (A) between door finisher and door panel
to disengage the clips and metal clip.
CAUTION:
Insert a remover tool (A) into the part shown in the figure.
(Between the clips and the door panel)
9.
Disconnect lock knob cable (1), inside handle cable (2), power
window switch harness connector (B) and mood lamp harness
connector (A).
10. Remove the front door finisher.
11. Remove the following parts after removing the door finisher.
• Front door inside handle. Refer to
DLK-223, "INSIDE HANDLE : Removal and Installation"
• Remove the front door grip fixing screws (A), then remove the
door grip from the door finisher (1).
• Remove the power window switch finisher. Refer to
INT-30, "DRIVER SIDE : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
: Clip
: Metal clip
JMJIA1770ZZ
JMJIA1769ZZ
JMJIA1955ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст