Nissan Teana J32. Manual — part 754
INT-36
< ON-VEHICLE REPAIR >
REAR DOOR FINISHER
REAR DOOR FINISHER
Exploded View
INFOID:0000000003819220
Removal and Installation
INFOID:0000000003819221
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
REMOVAL
1.
Fully open door window.
1.
Rear door panel
2.
Rear door inside handle
3.
Rear door power window switch fin-
isher
4.
Rear door finisher
5.
Rear door grip cover
6.
Rear door grip
7.
Inside handle escutcheon
8.
Cap
9.
Rear door power window switch
: Clip
: Pawl
JMJIA1800ZZ
REAR DOOR FINISHER
INT-37
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Remove inside handle escutcheon (1) with a flat-bladed screw-
driver (A) wrapped in a tape as shown in the figure.
3.
Remove screw (A) located on the back side of inside handle
escutcheon.
4.
Disengage the rear door grip cover (1) and cap (2) fixing pawls
with remover tool (A).
5.
Remove the rear door grip fixing bolt (A) with a tool.
6.
Remove the rear door finisher fixing bolt as shown in the figure
with tool (A).
: Pawl
JMJIA1755ZZ
JMJIA1757ZZ
: Pawl
JMJIA1762ZZ
JMJIA1764ZZ
JMJIA1766ZZ
INT-38
< ON-VEHICLE REPAIR >
REAR DOOR FINISHER
7.
Insert a remover tool (A) between the door finisher and door
panel to disengage the clips.
CAUTION:
Insert a remover tool (A) into the part shown in the figure.
(Between the clips and the door panel)
8.
Disconnect lock knob cable (1) and inside handle cable (2) from
rear inside handle (3).
9.
Disconnect the rear door power window switch harness connector.
10. Disconnect the mood lamp harness connector. Refer to
INL-91, "REAR DOOR GRIP : Exploded View"
.
11. Remove the rear door finisher.
12. Remove the following parts after removing the rear door finisher.
• Rear door inside handle. Refer to
DLK-228, "INSIDE HANDLE : Removal and Installation"
.
• Remove the rear door grip fixing screws (A), then remove the
rear door grip from the door finisher (1).
• Remove the rear power window switch finisher. Refer to
INT-30, "DRIVER SIDE : Removal and Installa-
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
: Clip
JMJIA1768ZZ
JMJIA1359ZZ
JMJIA1956ZZ
BODY SIDE TRIM
INT-39
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000003819222
Removal and Installation
INFOID:0000000003819223
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• Never damage the body.
REMOVAL
FRONT PILLAR GARNISH
1.
Release front pillar portion of front body side welt.
1.
Front pillar garnish
2.
Front body side welt
3.
Front kicking plate outer
4.
Dash side finisher
5.
Front kicking plate inner
6.
Center pillar lower garnish
7.
Rear kicking plate inner
8.
Rear kicking plate outer
9.
Rear body side welt
10. Rear pillar finisher
11. Center pillar upper garnish
: Clip
: Pawl
: Metal clip
JMJIA1801ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст