Nissan Teana J32. Manual — part 605
EXT-30
< ON-VEHICLE REPAIR >
ROOF SIDE MOLDING
3.
Remove roof side molding after sliding it in the backward direc-
tion of the vehicle.
CAUTION:
The position of roof side molding front end fixing clip moves when removing roof side molding.
Before removing the roof side molding, always check and mark the position of roof side molding front
end fixing clip. Put matching marks between the molding and the roof side molding and the body side
panel or the glass.
INSTALLATION
1.
Reinstall roof side molding front end fixing clips that is removed from the vehicle to the matching mark
position of the molding.
2.
Align the matching mark positions of the molding and vehicle, and install from the front end to rear end.
CAUTION:
When installing, visually check the roof side molding and the clips, then replace them with new parts if
they are damaged.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Remove roof side molding. Refer to
EXT-29, "Removal and Installation"
.
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape clips after press fit, and temporarily hold it for specified time based on the following.
6.
Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:
• Use double-faced adhesive tape after hardening for clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
: Clip
JMKIA2616ZZ
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
ROOF SIDE MOLDING
EXT-31
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Never wash the vehicle with in 24 hours so as to keep adhesive.
EXT-32
< ON-VEHICLE REPAIR >
DRIP MOLDING
DRIP MOLDING
Exploded View
INFOID:0000000003894989
Removal and Installation
INFOID:0000000003894990
Removal
1.
Fully open front door and rear door.
2.
Remove drip molding (1) fixing clips from front end to rear end
using remover tool (A).
CAUTION:
Apply protective tape (B) around the drip molding.
Installation
Install in the reverse order of removal.
CAUTION:
When installing, check visually the drip molding and clips, then replace them with new parts if they are
damaged.
1.
Drip molding
: Clip
JMKIA2665ZZ
: Clip
JMKIA2666ZZ
DOOR OUTSIDE MOLDING
EXT-33
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
DOOR OUTSIDE MOLDING
Exploded View
INFOID:0000000003819549
Removal and Installation
INFOID:0000000003819550
REMOVAL
FRONT DOOR OUTSIDE MOLDING
1.
Remove front door finisher. Refer to
INT-30, "DRIVER SIDE : Removal and Installation"
.
2.
Remove door mirror assembly. Refer to
MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
3.
Twists and pull up to upper side, and then remove front door out-
side molding (1).
1.
Rear door outside molding
2.
Rear door panel
3.
Front door panel
4.
Front door outside molding
: Pawl
Refer to
for symbols in the figure.
JMKIA2657ZZ
JMKIA0116GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст