Nissan Teana J32. Manual — part 1057
SPIRAL CABLE
SR-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SR-12
< ON-VEHICLE REPAIR >
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000003838669
Removal and Installation
INFOID:0000000003838670
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Always work from the side of air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the instrument panel assembly. Refer to
IP-12, "Removal and Installation"
.
2.
Remove the front passenger air bag module fixing screws (A).
3.
Disconnect pawls by using remover tool, and then remove front
passenger air bag module (2) from instrument panel (1).
CAUTION:
1.
Instrument panel assembly
2.
Front passenger air bag module
Refer to
for symbols in the figure.
JMHIA0619GB
: Pawl
JMHIA0621ZZ
FRONT PASSENGER AIR BAG MODULE
SR-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Always place front passenger air bag module (1) with pad side
facing upward.
• Never impact the front passenger air bag module.
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
• Never disassembly front passenger air bag module.
• Never expose the front passenger air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use old fixing bolts after removal; replace with new bolts.
• In the case that a malfunction is detected by the air bag warning lamp, after repair or replacement of
the malfunctioning parts, reset the memory by self-diagnosis or by CONSULT-III.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-10, "Diagnosis Description"
: Upward
JMHIA0622ZZ
JMHIA0009ZZ
SR-14
< ON-VEHICLE REPAIR >
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000003838671
Removal and Installation
INFOID:0000000003838672
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the headlining assembly.
• Normal roof models: Refer to
INT-50, "NORMAL ROOF : Removal and Installation"
.
• Sunroof models: Refer to
INT-54, "SUNROOF : Removal and Installation"
.
2.
Remove the side curtain air bag harness connector.
NOTE:
• For installing/removing side curtain air bag harness connector,
insert thin screwdriver wrapped in tape into notch, lift lock and
remove connector.
• Install connector with lock raised, and push lock into connec-
tor.
• After installing the connector, check that the lock is pushed
securely into it.
1.
Side curtain air bag module
Refer to
for symbols in the figure.
JMHIA0623GB
PHIA0953J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст