Nissan Teana J32. Manual — part 35
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
ADP-133
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000003759234
1.
CHECK DOOR LOCK FUNCTION
Check door lock function.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
PERFORM MEMORY STORING PROCEDURE
1.
Perform memory storing procedure.
Refer to
ADP-9, "MEMORY STORING : Special Repair Requirement"
2.
Check Intelligent Key interlock function.
Refer to
ADP-31, "INTELLIGENT KEY INTERLOCK FUNCTION : System Description"
.
Is the inspection result normal?
YES
>> Intelligent Key inter lock function is normal.
NO
>> Replace driver seat control unit. Refer to
ADP-134
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000003759236
The following symptoms are normal operations, and they do not indicate a malfunction.
Symptom
Cause
Action to take
Reference page
Entry/exit assist function and
seat synchronization do not op-
erate.
No initialization has been performed.
Perform initialization.
Entry/exit assist function is disabled.
NOTE:
The entry/exit assist function and seat
synchronization function are disabled be-
fore delivery (initial setting).
Change the settings.
Entry assist function does not op-
erate.
Manual operation with power seat switch
was performed after exit assist function
execution.
Perform the memory
function.
Memory function, entry/exit as-
sist function, or Intelligent Key in-
terlock function does not
operate.
The operating conditions are not fulfilled.
Fulfill the operation
conditions.
Memory function:
Exit assist function:
Entry assist function:
Intelligent Key interlock
function:
PRECAUTIONS
ADP-135
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003940050
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
ADP-136
< ON-VEHICLE REPAIR >
DRIVER SEAT CONTROL UNIT
ON-VEHICLE REPAIR
DRIVER SEAT CONTROL UNIT
Exploded View
INFOID:0000000003759238
Removal and Installation
INFOID:0000000003759239
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the driver seat (1). Refer to
.
2.
Remove the mounting nut (A).
3.
Remove driver seat control unit (2).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to clump the harness to the right place.
NOTE:
After installing the driver seat, perform additional service when replacing control unit. Refer to
TIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
JMJIA1449ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст