Nissan Teana J32. Manual — part 1199
TM-320
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
CONTROL CABLE
8.
Remove control cable (1) from bracket 1 (2).
9.
Remove nuts (
).
10. Remove rear foot duct 1 (right). Refer to
11. Remove the control cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing the control cable (1) to the control device assembly
(2), make sure that the control cable is fully pressed in with the
ribbed (A) surface facing upward.
Inspection and Adjustment
INFOID:0000000003806520
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing control cable. Refer to
TM-314, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-314, "Inspection and Adjustment"
: Vehicle front
JPDIA0752ZZ
JPDIA0609ZZ
OIL PAN
TM-321
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000003806524
Removal and Installation
INFOID:0000000003806525
REMOVAL
1.
Remove drain plug (1), and then drain CVT fluid from oil pan.
2.
Remove oil pan fitting bolts (2).
3.
Remove oil pan (3).
4.
Remove oil pan gasket from oil pan.
5.
Remove magnet from oil pan.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mounting surface of
transaxle case and oil pan.
• Never reuse oil pan gasket, drain plug gasket and oil pan fitting bolts.
1.
Transaxle assembly
2.
Oil pan gasket
3.
Magnet
4.
Drain plug gasket
5.
Drain plug
6.
Oil pan fitting bolt
7.
Oil pan
Refer to
JPDIA0769GB
: Vehicle front
JPDIA0761ZZ
TM-322
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
OIL PAN
Inspection
INFOID:0000000003806526
Check foreign materials in oil pan to help determine causes of malfunction. If the CVT fluid is very dark, smells
burned, or contains foreign particles, frictional material (clutches) may need replacement. A tacky film that will
not wipe clean indicates varnish build up. Varnish can cause valves and clutches to stick and can inhibit pump
pressure.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
PRIMARY SPEED SENSOR
TM-323
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PRIMARY SPEED SENSOR
Exploded View
INFOID:0000000003806530
Removal and Installation
INFOID:0000000003806531
REMOVAL
1.
Remove the air duct (inlet) and air cleaner case. Refer to
.
2.
Remove the battery.
3.
Disconnect ECM connector and TCM connector.
4.
Remove battery bracket.
5.
Remove CVT fluid level gauge and CVT fluid charging pipe. Refer to
6.
Disconnect primary speed sensor connector.
7.
Remove primary speed sensor.
8.
Remove O-ring from primary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000003806532
After completing installation, check for CVT fluid leakage and check CVT fluid level. Refer to
.
1.
Primary speed sensor
2.
O-ring
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0770GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст