Nissan Tiida C11. Manual — part 300
DLK-610
< BASIC INSPECTION >
[WITHOUT I-KEY, WITH SUPER LOCK]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000001397190
OVERALL SEQUENCE
DETAILED FLOW
ALKIA0246GB
DIAGNOSIS AND REPAIR WORKFLOW
DLK-611
< BASIC INSPECTION >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC for BCM.
2.
Perform the following procedure if DTC is displayed.
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to
DLK-716, "DTC Inspection Priority Chart"
and determine trouble
diagnosis order.
Is DTC detected?
YES
>> GO TO 8.
NO
>> Refer to
XX-XX, "*****"
.
6.
PERFORM BASIC INSPECTION
Perform Basic Inspection, refer to
Inspection End>>GO TO 7.
7.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to Symptom Table based on the confirmed symptom in step 4.
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 9.
DLK-612
< BASIC INSPECTION >
[WITHOUT I-KEY, WITH SUPER LOCK]
DIAGNOSIS AND REPAIR WORKFLOW
9.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is displayed, erase it.
>> GO TO 10.
10.
FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO
>> INSPECTION END
INSPECTION AND ADJUSTMENT
DLK-613
< BASIC INSPECTION >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000001397191
Perform the system initialization when replacing or registering Keyfob and ignition key.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000001397192
Refer to the CONSULT-III Operation Manual-NATS.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст