Nissan Tiida C11. Manual — part 674
EM-48
< ON-VEHICLE REPAIR >
[HR16DE]
IGNITION COIL, SPARK PLUG AND ROCKER COVER
5.
Remove fuel tube protector.
6.
Remove oil filler cap.
7.
Remove rocker cover.
• Loosen bolts in reverse order shown.
NOTE:
13 and 14 shown are used to tighten the fuel tube protector.
8.
Remove rocker cover gasket from rocker cover.
9.
Use scraper to remove all traces of liquid gasket from cylinder head and front cover.
CAUTION:
Never scratch or damage the mating surface when cleaning off old liquid gasket.
INSTALLATION
1.
Install the rocker cover with the following procedure.
a.
Install the gasket to the rocker cover.
• Check for damage or foreign material.
• Make sure that it is securely inserted in the mounting groove of
rocker cover.
• For the 2 bolt holes shown, push the gasket into the boss for
the rocker cover bolt hole to prevent it from falling.
b.
Apply liquid gasket to the position shown.
Use Genuine Liquid Gasket or equivalent.
2.
Install rocker cover to the cylinder head.
CAUTION:
Make sure the gasket is not dropped.
3.
Install rocker cover.
: Engine front
PBIC3670E
KBIA3331J
1
: Cylinder head
2
: Front cover
PBIC3671E
IGNITION COIL, SPARK PLUG AND ROCKER COVER
EM-49
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Tighten bolts in two steps separately in numerical order as
shown.
4.
Install in the reverse order of removal, for the remaining parts.
: Engine front
PBIC3670E
EM-50
< ON-VEHICLE REPAIR >
[HR16DE]
TIMING CHAIN
TIMING CHAIN
Exploded View
INFOID:0000000001381411
Removal and Installation
INFOID:0000000001381412
CAUTION:
The rotation direction indicated in the text indicates all directions seen from the engine front direction.
REMOVAL
1.
Remove front wheel (RH). Refer to
2.
Remove front fender protector (RH). Refer to
EXT-22, "Removal and Installation"
.
3.
Drain engine oil. Refer to
.
CAUTION:
Be sure to perform this step when engine is cold.
1.
Timing chain slack guide
2.
Chain tensioner (for timing chain)
3.
Camshaft sprocket (EXH)
4.
Camshaft sprocket (INT)
5.
Plug
6.
Front oil seal
7.
Crankshaft pulley
8.
Crankshaft pulley bolt
9.
Front cover
10. Crankshaft sprocket
11. Oil pump sprocket
12.
Oil pump drive chain
13. Chain tensioner (for oil pump drive chain) 14. Timing chain
15.
Timing chain tension guide
A.
Refer to
PBIC3709E
TIMING CHAIN
EM-51
< ON-VEHICLE REPAIR >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4.
Remove the following parts.
• Intake manifold: Refer to
• Drive belt: Refer to
EM-16, "Removal and Installation"
• Water pump pulley: Refer to
• Ground cable (RH)
5.
Support the bottom surface of engine using a transmission jack, and then remove the engine mounting
bracket and insulator (RH). Refer to
6.
Remove rocker cover. Refer to
7.
Set No. 1 cylinder at TDC of its compression stroke with the following procedure:
a.
Rotate crankshaft pulley (2) clockwise and align TDC mark
(without paint mark) (A) to timing indicator (1) on front cover.
b.
Make sure the matching marks on each camshaft sprocket are
positioned as shown.
• If not, rotate crankshaft pulley one more turn to align matching
marks to the positions.
8.
Remove crankshaft pulley with the following procedure:
a.
Secure crankshaft pulley (1) using a suitable tool (A).
b.
Loosen and pull out crankshaft pulley bolts.
CAUTION:
Never remove the mounting bolts as they are used as a sup-
porting point for the pulley puller.
c.
Attach a pulley puller [SST: KV11103000] (A) in the M 6 thread
hole on crankshaft pulley, and remove crankshaft pulley.
B
: White paint mark (Not use for service)
PBIC3673E
1
: Camshaft sprocket (EXH)
2
: Camshaft sprocket (INT)
A
: Matching mark (stamp)
B
: Matching mark (peripheral stamp line)
PBIC3872E
PBIC3710E
B
: M6 bolt
PBIC3711E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст