Nissan Tiida C11. Manual — part 336
DLK-754
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY, WITH SUPER LOCK]
REAR DOOR LOCK
REAR DOOR LOCK
Component Parts Location
INFOID:0000000001732064
Removal and Installation
INFOID:0000000001732065
REMOVAL
1.
Remove the partition glass. Refer to
XX-XX, "*****"
.
2.
Support door glass while lifting it up to the door window completely closed position.
3.
Remove inside handle bolt, slide handle toward rear of vehicle,
disconnect it from the door panel, and remove the inside handle.
4.
Disconnect the inside handle and lock knob cables from the
inside handle.
CAUTION:
During removal and installation, do not to bend the ends of
the lock knob cable and inside handle cable.
1.
Rear door
2.
Inside handle
3.
Inside handle cable
4.
Door lock assembly
5.
TORX bolt (T30)
6.
Outside handle cable
7.
Grommet
8.
TORX bolt (T30)
9.
Rear gasket
10. Outside handle escutcheon
11. Outside handle
12. Front gasket
13. Lock knob cable
14. Outside handle bracket
PIIB6530E
PIIB6524E
PIIB6525E
REAR DOOR LOCK
DLK-755
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove the door side grommet, and the outside handle
escutcheon screw.
6.
Pull the outside handle forward (1), while removing outside han-
dle escutcheon (2).
7.
Pull outside door handle forward (1), and slide it toward the rear
of the vehicle to remove (2).
8.
Remove the front and rear gaskets.
9.
Remove the door lock assembly screws.
PIIB5808E
PIIB5809E
PIIB5810E
PIIB6526E
: 5.8 N·m (0.6 kg-m, 51.4 in-lb)
PIIB6527E
DLK-756
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY, WITH SUPER LOCK]
REAR DOOR LOCK
10. Slide the outside handle bracket toward the rear of vehicle,
remove the outside handle bracket and the door lock assembly.
11. If equipped, disconnect the door lock assembly electrical connector.
12. Disconnect the outside handle cable from the outside handle
bracket.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• To install each rod, be sure to rotate the rod holder until a click is felt.
• When installing door lock assembly, be careful when rotating the outside handle cable as shown.
- Place the outside handle bracket cable on the inside of door
lock assembly before installing.
PIIB6528E
PIIB5815E
PIIB6529E
BACK DOOR LOCK
DLK-757
< REMOVAL AND INSTALLATION >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR LOCK
Removal and Installation
INFOID:0000000001732066
BACK DOOR LOCK
Removal
1.
Remove the back door finisher lower. Refer to
XX-XX, "*****"
.
2.
Remove the bolts, disconnect the electrical connector and sepa-
rate the lock from the door.
Installation
Installation is in the reverse order of removal.
BACK DOOR HANDLE
Removal
1.
Remove the back door finisher lower. Refer to
XX-XX, "*****"
.
2.
Disconnect the harness connectors (1), remove the nuts and the
back door handle (A).
3.
Release the clips and remove the switch from the housing.
Installation
Installation is in the reverse order of removal.
LIIA2607E
LIIA2669E
LIIA2609E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст