Nissan Tiida C11. Manual — part 168
DLK-82
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
IGNITION KNOB SWITCH
>> INSPECTION END
Component Inspection
INFOID:0000000001396563
1.
CHECK IGNITION KNOB SWITCH
1.
Turn ignition switch OFF.
2.
Check continuity between key switch and ignition knob switch
terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace key switch and ignition knob switch.
PIIA6140E
key switch and ignition knob switch
Condition
Continuity
Terminals
3
4
Ignition knob switch is pressed
Yes
Ignition knob switch is released
No
DOOR REQUEST SWITCH
DLK-83
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR REQUEST SWITCH
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000001396524
Transmits lock/unlock operation to Intelligent Key unit.
DRIVER SIDE : Component Function Check
INFOID:0000000001396525
1.
CHECK FUNCTION
With CONSULT-III
Check door request switch “DR REQ SW” in “Data Monitor” mode.
Is the inspection result normal?
YES
>> Door request switch is OK.
NO
>> Refer to
DLK-83, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000001396526
1.
CHECK INTELLIGENT KEY UNIT INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between Intelligent Key unit harness connector
and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK FRONT DOOR REQUEST SWITCH CIRCUIT
1.
Disconnect Intelligent Key unit and driver door request switch.
Monitor item
Condition
DR REQ SW
Door request switch is pressed
:ON
Door request switch is released
:OFF
ALKIA0741ZZ
Terminal
Door request
switch condition
Voltage (V)
(Approx.)
(+)
(–)
Intelligent Key unit
connector
Terminal
M52
5
Ground
Pressed
0
Released
5
DLK-84
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR REQUEST SWITCH
2.
Check continuity between Intelligent Key unit connector (A) M52
terminal 5 and front door request switch (driver side) connector
(B) D5 terminal 1.
3.
Check continuity between Intelligent Key unit connector (A) M52
terminal 5 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness between Intelligent Key unit and front door request switch (driver side).
3.
CHECK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between front door request switch (driver side) con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace front door request switch (driver side) ground circuit.
4.
CHECK INTELLIGENT KEY UNIT OUTPUT SIGNAL
1.
Connect Intelligent Key unit connector.
2.
Check voltage between Intelligent Key unit connector and
ground.
Intelligent Key unit
connector
Terminal
Front door request switch
(driver side)
Terminal
Continuity
M52
5
D5
1
Yes
Intelligent Key unit
connector
Terminal
Ground
Continuity
M52
5
No
ALKIA0742ZZ
PIIB7427E
Front door request switch (driver side)
connector
Terminal
Ground
Continuity
D5
2
Yes
ALKIA0741ZZ
Intelligent Key unit
connector
Terminal
Ground
Voltage (V)
(Approx.)
M52
5
5
DOOR REQUEST SWITCH
DLK-85
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
CHECK DOOR REQUEST SWITCH
Check door request switch.
Refer to
DLK-85, "DRIVER SIDE : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace front outside handle (driver side). Refer to
XX-XX, "*****"
and
XX-XX, "*****"
.
6.
CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
DRIVER SIDE : Component Inspection
INFOID:0000000001396527
1.
CHECK DOOR REQUEST SWITCH
Check door request switch.
Is the inspection result normal?
YES
>> Door request switch is OK.
NO
>> Replace front outside handle (driver side). Refer to
XX-XX, "*****"
and
XX-XX, "*****"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000001396528
Transmits lock/unlock operation to Intelligent Key unit.
PASSENGER SIDE : Component Function Check
INFOID:0000000001396529
1.
CHECK FUNCTION
With CONSULT-III
Check door request switch “AS REQ SW” in “Data Monitor” mode.
Is the inspection result normal?
PIIB7426E
Terminal
Door request switch condition
Continuity
front door request switch (driver side)
1
2
Pressed
Yes
Released
No
Monitor item
Condition
AS REQ SW
Door request switch is pressed
:ON
Door request switch is released
:OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст