Nissan Tiida C11. Manual — part 705
EM-172
< ON-VEHICLE REPAIR >
[MR18DE]
IGNITION COIL
IGNITION COIL
Component
INFOID:0000000001346465
Removal and Installation
INFOID:0000000001346466
REMOVAL
1.
Remove intake manifold. Refer to
EM-156, "Removal and Installation"
2.
Remove ignition coil.
CAUTION:
• Handle it carefully and avoid impacts.
• Never disassemble.
INSTALLATION
1.
Install ignition coil.
CAUTION:
• Handle it carefully and avoid impacts.
• Never disassemble.
2.
Install intake manifold. Refer to
EM-156, "Removal and Installation"
.
1.
PCV hose
2.
Rocker cover
3.
Spark plug
4.
Ignition coil
5.
PCV hose
6.
PCV valve
7.
O-ring
8.
Gasket
A.
To air duct
B.
Refer to
.
C.
To intake manifold
PBIC3536J
ROCKER COVER
EM-173
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ROCKER COVER
Component
INFOID:0000000001346467
Removal and Installation
INFOID:0000000001346468
REMOVAL
1.
Remove intake manifold. Refer to
EM-156, "Removal and Installation"
2.
Remove ignition coil.
CAUTION:
• Handle it carefully and avoid impacts.
• Never disassemble.
1.
PCV hose
2.
Rocker cover
3.
Spark plug
4.
Ignition coil
5.
PCV hose
6.
PCV valve
7.
O-ring
8.
Gasket
A.
To air duct
B.
C.
To intake manifold
PBIC3536J
EM-174
< ON-VEHICLE REPAIR >
[MR18DE]
ROCKER COVER
3.
Remove spark plug using suitable tool.
CAUTION:
Never drop or shock it.
4.
Remove rocker cover.
• Loosen bolts in reverse order as shown.
•
Engine front
INSPECTION AFTER REMOVAL
CAUTION:
• Never drop or shock spark plug.
• Checking and adjusting spark plug gap is not required
between change intervals.
• If spark plug tip is covered with carbon, a spark plug cleaner may be used.
• Never use wire brush for cleaning spark plug.
INSTALLATION
1.
Install rocker cover gasket to rocker cover.
PBIC3871E
PBIC3151J
SMA806CA
Cleaner air pressure
: Less than 588 kPa (5.88 bar, 6 kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
SMA773C
ROCKER COVER
EM-175
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Install rocker cover.
• Tighten bolts in two steps separately in numerical order as
shown.
•
Engine front
CAUTION:
Check if rocker cover gasket is not dropped from the instal-
lation groove of rocker cover.
3.
Install spark plug using suitable tool.
CAUTION:
Never drop or shock it.
4.
Install ignition coil.
CAUTION:
• Handle it carefully and avoid impacts.
• Never disassemble.
5.
Install intake manifold. Refer to
EM-156, "Removal and Installation"
1st step
: 1.96 N·m (0.20 kg-m, 17 in-lb)
2nd step
: 8.33 N·m (0.85 kg-m, 73 in-lb)
PBIC3151J
PBIC3871E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст