Nissan Tiida C11. Manual — part 704
EM-168
< ON-VEHICLE REPAIR >
[MR18DE]
OIL PAN
9.
Insert a screwdriver shown by the arrow (
) and open up a
crack between oil pan (upper) and cylinder block.
CAUTION:
A more adhesive liquid gasket is applied compared to previ-
ous types when shipped, so it should not be forced off the
position not specified.
10. After removing the bolts, separate the mating surface and
remove the sealant using Tool.
• Slide (1) the Tool by tapping (2) its side with a hammer to
remove the lower oil pan from the upper oil pan.
CAUTION:
Be careful not to damage the mating surfaces.
11. Remove O-ring between cylinder block and oil pan (upper).
INSPECTION AFTER REMOVAL
Oil Filter
Clean oil strainer portion (part of the oil pump) if any object attached.
INSTALLATION
1.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
• Remove the old liquid gasket from mating surface of cylinder
block.
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
: Engine front
PBIC3534J
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC3949E
OIL PAN
EM-169
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Apply the sealant without breaks to the specified location using
Tool.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-27, "Recommended Chemical Products and Sealants"
.
CAUTION:
Apply liquid gasket to outside of bolt hole for the positions
shown by marks.
3.
Install new O-ring at cylinder block side.
CAUTION:
Install avoiding misalignment of O-ring.
4.
Tighten bolts in numerical order as shown.
5.
Install rear oil seal with the following procedure.
CAUTION:
• The installation of rear oil seal should be completed within 5 minutes after installing oil pan
(upper).
• Always replace rear oil seal with new one.
• Never touch oil seal lip.
a.
Wipe off liquid gasket protruding to the rear oil seal mating part of oil pan (upper) and cylinder block using
a scraper.
b.
Apply engine oil to entire outside area of rear oil seal.
Tool number
WS39930000 (
–
)
1
: Oil pan (upper)
A
: 2 mm protruded to outside
B
: 2 mm protruded to rear oil seal mounting side
: Engine front
: Engine outside
PBIC4587E
: Engine front
PBIC3533J
EM-170
< ON-VEHICLE REPAIR >
[MR18DE]
OIL PAN
c.
Press-fit the rear oil seal using a drift with outer diameter 115
mm (4.53 in) and inner diameter 90 mm (3.54 in) (A) (commer-
cial service tool).
• Press-fit to the specified dimensions as shown.
CAUTION:
• Never touch the grease applied to the oil seal lip.
• Be careful not to damage the rear oil seal mounting part of
oil pan (upper) and cylinder block or the crankshaft.
• Press-fit straight, making sure that rear oil seal does not
curl or tilt.
NOTE:
The standard surface of the dimension is the rear end surface of
cylinder block.
6.
Install oil pump.
• Tighten bolts in numerical order as shown.
7.
Install oil pump sprocket, oil pump drive chain and other related
parts if removed.
8.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and threads.
PBIC3951E
1
: Rear oil seal
A
: Cylinder block rear end surface
1
: Oil pump
2
: Oil pan (upper)
: Engine front
PBIC3952E
PBIC3532J
PBIC3953E
OIL PAN
EM-171
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
9.
Apply the sealant without breaks to the specified location using
Tool.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-27, "Recommended Chemical Products and Sealants"
.
10. Tighten bolts in numerical order as shown.
11. Install oil filter with the following procedure:
a.
Remove foreign materials adhering to the oil filter installation
surface.
b.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
c.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
12. Installation of the remaining components is in the reverse order of removal.
Tool number
WS39930000 (
–
)
1
: Oil pan (lower)
: Engine outside
PBIC4590E
: Engine front
PBIC3146J
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA229B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст