Nissan Tiida C11. Manual — part 202
DLK-218
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
HOOD
1.
Check that the secondary latch is properly engaged with the secondary striker (B: 6.8 mm (0.268 in) with
hood's own weight.
2.
While operating the hood release handle, carefully check that the front end of the hood is raised by
approx. 20 mm (0.79 in). Also check that the hood release handle returns to the original position.
3.
Check that the secondary hood release operates at 29.4 N (3.0 kg) or below.
4.
Confirm static closing force of the hood is 343 – 441 N·m (35 – 44 kg-m).
5.
Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points as shown.
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
PIIB5794E
PIIB6514E
RADIATOR CORE SUPPORT
DLK-219
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Removal and Installation
INFOID:0000000001315835
REMOVAL
Radiator Core Support Upper
1.
Remove the air duct. Refer to
EM-27, "Removal and Installation"
(MR18DE), or
EM-269, "Removal and Installation"
(K9K).
2.
Remove the headlamp (LH/RH). Refer to
EXL-84, "Removal and Installation"
3.
Remove the hood lock assembly, and remove hood lock cable. Refer to
4.
Remove the air guide and hood lock cable clip.
5.
Remove the washer tank inlet. Refer to
WW-64, "Removal and Installation"
.
6.
Remove the radiator core support upper.
Radiator Core Support Lower
1.
Remove the air duct. Refer to
EM-27, "Removal and Installation"
(MR18DE), or
EM-269, "Removal and Installation"
(K9K).
2.
Remove the front bumper. Refer to
EXT-13, "Removal and Installation"
3.
Remove the headlamp (LH/RH). Refer to
EXL-84, "Removal and Installation"
4.
Remove the hood lock assembly, and remove hood lock cable. Refer to
5.
Remove the air guide and hood lock cable mounting clip.
6.
Remove the front bumper reinforcement. Refer to
EXT-13, "Removal and Installation"
.
7.
Remove the radiator core lower stay.
8.
Remove the undercover.
PIIB6515E
1.
Radiator core support upper
2.
Radiator core support lower
3.
Radiator core support lower stay
4.
Radiator core support side stay
5.
Air guide
24.5 N·m (2.5 kg-m, 18 ft-lb)
DLK-220
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
RADIATOR CORE SUPPORT
9.
Remove radiator core support lower side stay.
10. Tie a cord to all radiator core upper supports of the radiator and
condenser.
NOTE:
To prevent the compressor and radiator from being dropped
when the radiator core lower support is removed.
11. Remove the bolts, and lower radiator core lower supports.
12. Remove the radiator core lower supports.
INSTALLATION
Installation is in the reverse order of removal.
55.0 N·m (5.6 kg-m, 41 ft-lb)
PIIB2800J
PIIB2799J
FRONT FENDER
DLK-221
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Removal and Installation
INFOID:0000000001315836
REMOVAL
1.
Remove the headlamp assemblies. Refer to
EXL-84, "Removal and Installation"
2.
Remove the cowl top cover (LH/RH). Refer to
EXT-20, "Removal and Installation"
.
3.
Remove the front fender protector. Refer to
DLK-221, "Removal and Installation"
.
4.
Remove the bolt and the front fender.
CAUTION:
While removing use a shop cloth to protect the vechicle body from damage.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installing, apply touch-up paint onto the head of the front fender bolts.
• After installing, check front fender adjustment. Refer to
1.
Front fender
2
Bolt (LH 7 bolts required) (RH 8 bolts
required)
LIIA2657E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст