Nissan Tiida C11. Manual — part 1311
REPAIR FOR COMPONENT PARTS
TM-295
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
a.
Place differential case in the upright position so that the side
gear to be measured is at the top.
(A): Location for inserting feeler gauge
(B): Side gear tooth
(C): The center line of differential case
b.
In order to maximize the back clearance, rotate side gears so
that a tooth on side gears at the top and bottom will align at the
same position as shown.
c.
Adjust the back clearance of side gear according to the following
procedures.
i.
Insert feeler gauges (A) of the same thickness to the back of
side gear from both sides, preventing side gear from falling, to
measure the clearance.
• Measure clearance 3 times by rotating side gears and take the
average.
CAUTION:
In all 3 measurements, maximize the clearance by aligning
teeth on side gears at the top and bottom at the same posi-
tion.
ii.
Select side gear thrust washer so that the clearance will fall
within the standard.
iii.
Turn differential case upside down, and measure the back clear-
ance of the other side gear in the same manner.
NOTE:
Adjust the clearance to approx. 0.1 mm (0.004 in) for used differ-
ential [driven approx. 3,000 km (1864 mile) or more].
3.
Install lock pin (1) to pinion mate shaft using Tool (A).
CAUTION:
Make sure that lock pin (1) flush with differential case.
4.
Set Tool (A) on differential side bearing (RH side) (1), and press
differential side bearing (RH side) (1) to differential case (2).
CAUTION:
Set Tool (A) on differential side bearing inner race.
SCIA7064E
Differential side gear clearance:
.
SCIA7061E
Tool number:
KV32101000
SCIA7228E
Tool number:
ST33200000
SCIA7062E
TM-296
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
5.
Set Tool (A) on differential side bearing (LH side) (1), and press
differential side bearing (LH side) (1) to differential case (2).
CAUTION:
Set Tool (A) on differential side bearing inner race.
6.
Install final gear on differential case, and tighten bolts to the
specified torque in the numerical order as shown.
Tool number:
ST33200000
SCIA7063E
SCIA0294J
ASSEMBLY
TM-297
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ASSEMBLY
Assembly (1)
INFOID:0000000001730996
1.
Drive transaxle case side oil seal (1) using Tools, and converter
housing side oil seal (2) using suitable tool, to the dimensions as
shown
(A): Transaxle case side
(B): Converter housing side
NOTE:
Differential side oil seal pulling direction is used as the reference.
2.
Install O-ring on governor cap.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
3.
Install governor cap in transaxle case.
4.
Install snap ring in transaxle case.
5.
Install parking actuator support (1) on transaxle case.
(A): Inside
(B): Outside
CAUTION:
Be careful with the direction of parking actuator support (1).
6.
Tighten parking actuator support bolts to the specified torque.
7.
Install parking pawl (2) on transaxle case, and secure it with
parking shaft (1).
Tool numbers
: ST35325000 (
—
)
: KV31103000 (
—
)
Dimension "C"
: 0
±±
Dimension "D"
: 1.1
±
0.5 mm (0.043
±
0.020 in)
SCIA7226E
SCIA5910J
SCIA6997E
TM-298
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
ASSEMBLY
8.
Install return spring (2) on parking shaft (3) and parking pawl (1)
using suitable tool.
Adjustment (1)
INFOID:0000000001730997
REDUCTION PINION GEAR BEARING PRELOAD
1.
Select proper thickness of reduction pinion gear adjusting shim using the following procedures.
a.
Place reduction pinion gear on transaxle case as shown.
b.
Install idler gear bearing outer race on transaxle case.
c.
Place idler gear bearing inner race on outer race.
d.
Measure dimensions “B”, “C” and “D”, and calculate dimension
“A”.
• Measure dimension “B” between the end of reduction pinion
gear and the surface of transaxle case.
• Measure dimension “B” in at least two places, and take
the average.
SCIA6996E
SCIA3623E
“A”:
Distance between the surface of idler gear bear-
ing inner race and the adjusting shim mating
surface of reduction pinion gear.
A = D
−
(B + C)
SCIA3624E
SCIA3625E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст