Nissan Tiida C11. Manual — part 1310
REPAIR FOR COMPONENT PARTS
TM-291
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Install O-rings to servo piston retainer
5.
Install band servo piston assembly to servo piston retainer by
pushing it inward.
6.
Install D-ring (1) to OD servo piston (2).
7.
Install O-rings (1), (2) and (3) to OD servo piston retainer (4).
(1): O-ring (small diameter)
(2): O-ring (medium diameter)
(3): O-ring (large diameter)
8.
Install OD servo piston (1) to OD servo piston retainer (2) as
shown.
SCIA3671E
SAT303D
SCIA7053E
SCIA6492J
SCIA7057E
TM-292
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
9.
Install 2nd servo return spring (2) and band servo piston assem-
bly (3) to transaxle case (1).
10. Install OD servo piston assembly (2) to transaxle case (1).
11. Push in OD servo piston assembly using suitable tool (A) and-
suitable tool (B), and install snap ring (1) to transaxle case using
suitable tool (C).
Final Drive
INFOID:0000000001730995
COMPONENTS
SCIA6310J
SCIA6010J
SCIA7050E
SCIA7184E
REPAIR FOR COMPONENT PARTS
TM-293
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DISASSEMBLY
1.
Remove final gear from differential case.
2.
Remove differential side bearings according to the following procedures.
a.
Set suitable tool (A) on differential case (1), and remove differ-
ential side bearing (RH side) (2) from differential case (1) using
suitable tool (B) and suitable tool (C).
b.
Set suitable tool (A) on differential case (1), and remove differ-
ential side bearing (LH side) (2) from differential case (1) using
suitable tool (B).
3.
Remove pinion mate gear and side gear according to the following procedures.
a.
Drive out lock pin from differential case (1) using Tool (A).
1.
Pinion mate gear thrust washer
2.
Pinion mate gear
3.
Pinion mate shaft
4.
Side gear
5.
Side gear thrust washer
6.
Lock pin
7.
Differential side bearing
8.
Differential case
9.
Final gear
10. Differential side bearing adjusting
shim
SCIA0286J
SCIA7059E
SCIA7060E
Tool number:
KV32101000
SCIA7034E
TM-294
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
b.
Remove pinion mate shaft from differential case.
c.
Rotate pinion mate gears and pinion mate gear thrust washers
to remove.
d.
Remove side gears and side gear thrust washers from differen-
tial case.
INSPECTION
Gears, Washers, Pinion Mate Shaft and Differential Case
Check the sliding surfaces for wear, seizure, crack or damage.
Replace if necessary.
Bearings
Make sure bearings roll freely and are free from noise, cracks, pitting
or wear. Replace if necessary.
ASSEMBLY
1.
Install pinion mate gears and side gears according to the following procedures.
a.
Attach side gear thrust washers to side gears, then install pinion
mate gear thrust washers and pinion mate gears in place.
CAUTION:
Apply plenty of ATF to each sliding / rotating surface before
assembly.
b.
Set 2 pinion mate gears and thrust washers on the same axis,
and while rotating them simultaneously, align them with the
insert hole of pinion mate shaft on differential case to insert pin-
ion mate shaft.
CAUTION:
After aligning 2 pinion mate gears with side gear teeth and
centering with pinion mate shaft, take pinion mate shaft out
and move pinion mate gears in place while rotating the them simultaneously.
2.
Select side gear thrust washers according to the following procedures.
SAT316D
MTK0135D
SPD715
SAT318D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст