Nissan Tiida C11. Manual — part 258
DLK-442
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
HOOD
REMOVAL AND INSTALLATION
HOOD
Fitting Adjustment
INFOID:0000000001732017
FRONT END HEIGHT ADJUSTMENT AND LATERAL/LONGITUDINAL CLEARANCE ADJUST-
MENT
1.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2.
Remove hood lock. Rotate bumper rubber to adjust height until
hood becomes 1.0 to 1.5 mm lower than the fender.
3.
Position hood lock and engage striker. Check hood lock and
striker for looseness. Tighten lock bolts to the specified torque.
4.
Install the front grille. Refer to
EXT-19, "Removal and Installa-
CAUTION:
Adjust the clearance between hood and other parts so that the
dimensional difference left and right is as follows.
SURFACE MISMATCH ADJUSTMENT
1.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
2.
Release hood lock, and adjust surface level difference of hood, fender, and headlamp according to the fit-
ting standard dimension, using RH and LH bumper rubbers.
3.
Install and align the hood lock until the center of the striker and the hood lock are vertically aligned.
PIIB6508E
Hood and headlamp (B - B)
: Less than 2.0 mm (0.08 in)
Hood and fender (C - C)
: Less than 1.5 mm (0.06 in)
Hood and fender (D - D)
: Less than 1.5 mm (0.06 in)
PIIB2526J
Hood and front bumper (A - A)
: -1.3 - 2.7 mm (-0.05 - 0.11 in)
Hood and fender (D - D)
: -0.4 - 1.7 mm (-0.16 - 0.07 in)
HOOD
DLK-443
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Press the hood lightly with [approx. 29 N (3 kg] of force and adjust A and B as shown.
5.
After adjustment tighten lock bolts to the specified torque.
6.
Install the front grille. Refer to
EXT-19, "Removal and Installation"
.
Removal and Installation
INFOID:0000000001732018
HOOD ASSEMBLY
Removal
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A
: 20 mm (0.79 in)
B
: 6.8 mm (0.268 in) min.
PIIB5794E
1.
Hood hinge
2.
Hood stay
3.
Radiator core seal rubber
4.
Hood assembly
5.
Hood insulator
6.
Hood stay holder
PIIB2528J
DLK-444
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
HOOD
1.
Remove hinge nuts on hood and remove hood assembly.
CAUTION:
Two technicians should be used to avoid damaging the
hood during removal.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Before installing hood hinge, apply anticorrosive agent onto the surfaces that make contact with the
vehicle body.
• After installing, perform hood fitting adjustment. Refer to
.
HOOD HINGE
Removal
1.
Remove hood assembly. Refer to
DLK-443, "Removal and Installation"
2.
Remove front fender. Refer to
DLK-450, "Removal and Installation"
3.
Remove bolts and the hood hinge.
Installation
Installation is in the reverse order of removal.
Removal and Installation of Hood Lock Control
INFOID:0000000001732019
LH Drive
12.7 N·m (1.3 kg-m, 9.4 ft-lb)
PIIB2529J
12.7 N·m (1.3 kg-m, 9.4 ft-lb)
PIIB2530J
PIIB6509E
HOOD
DLK-445
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RH Drive
REMOVAL
Hood Lock
1.
Remove front grille (LH or RH as necessary). Refer to
EXT-19, "Removal and Installation"
2.
Remove hood lock bolts.
3.
Remove hood lock from hood lock cable.
Hood Lock Reinforcement
1.
Remove front bumper. Refer to
EXT-15, "Removal and Installation - Hatchback"
2.
Remove crash zone sensor.
3.
Remove bolts, and the hood lock reinforcement.
Hood Lock Cable
1.
Remove front grille (LH/RH). Refer to
EXT-19, "Removal and Installation"
2.
Remove fender protector (LH or RH as necessary). Refer to
EXT-22, "Removal and Installation"
3.
Remove hood lock, and remove hood lock cable from hood lock.
4.
Remove radiator core upper support, hood ledge, and then remove hood lock cable.
1.
Hood lock
2.
Hood lock cable
3.
Hood ledge upper front
4.
Clip
ALKIA0638GB
1.
Hood lock
2.
Hood lock cable
3.
Hood ledge upper front
4.
Clip
23.6 N·m (2.4 kg-m, 17 ft-lb)
23.6 N·m (2.4 kg-m, 17 ft-lb)
PIIB6511E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст