Nissan Tiida C11. Manual — part 1235
STR-26
< BASIC INSPECTION >
[K9K]
DIAGNOSIS AND REPAIR WORKFLOW
NOTE:
If any malfunction is found, immediately disconnect the battery cable from the negative terminal.
1.
CHECK ENGINE START
Crank the engine and check that the engine starts.
Does the engine start?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK THAT THE STARTER MOTOR STOPS
Check that the starter motor stops after starting the engine.
Does the starter motor stop?
YES
>> INSPECTION END.
NO
>> Replace starter motor.
3.
CHECK THE ENGINE SPEED WITH CRANKING
Check that the engine runs at cranking.
Does engine turn by cranking?
YES
>> GO TO 4
NO
>> GO TO 5
4.
CHECK THE ENGINE SPEED WITH CRANKING
Check that the engine speed is not low at cranking.
Does engine turn normally?
YES
>> Check ignition/fuel system.
NO
>> Check charge condition, corrosion and connection condition of the battery. Refer to
.
5.
CHECK STARTER MOTOR ACTIVATION
Check that the starter motor runs at cranking.
Does starter motor turn?
YES
>> GO TO 6
NO
>> GO TO 7
6.
ENGINE ROTATION STATUS
Check that the engine can be rotated by hand.
Does engine turn freely by hand?
YES
>> Replace starter motor.
NO
>> Perform further diagnosis of engine mechanical or powertrain mechanism. Refer to EM, TM or CL
sections.
7.
CHECK POWER SUPPLY CIRCUIT
Check the following conditions.
• Fuse and fusible link
• Charge condition, corrosion and connection condition of the battery. Refer to
Are these inspection results normal?
YES
>> GO TO 8
NO
>> Repair as needed.
8.
CHECK STARTING SYSTEM WIRING
Check the following.
• “B” terminal circuit. Refer to
• “S” terminal circuit. Refer to
Are these inspection results normal?
YES
>> GO TO 9
NO
>> Repair as needed.
DIAGNOSIS AND REPAIR WORKFLOW
STR-27
< BASIC INSPECTION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
9.
CHECK MAGNETIC SWITCH OPERATION SOUND
Check that a magnetic switch operation sound can be heard when the ignition switch is set at the starting posi-
tion.
Does magnetic switch operation sound occur?
YES
>> GO TO 10
NO
>> Replace starter motor.
10.
PINION AND RING GEAR ENGAGEMENT CHECK
Check condition of pinion and ring gear mesh.
Is the inspection result normal?
YES
>> Replace starter motor.
NO
>> GO TO 11
11.
CHECK STARTER MOTOR UNIT
Check the following.
• Check pinion moving mechanism.
• Check ring gear.
Are these inspection results normal?
YES
>> INSPECTION END.
NO
>> Repair or replace, if necessary.
STR-28
< FUNCTION DIAGNOSIS >
[K9K]
STARTING SYSTEM
FUNCTION DIAGNOSIS
STARTING SYSTEM
System Diagram
INFOID:0000000001728574
System Description
INFOID:0000000001728575
The starter motor plunger closes and provides a closed circuit between the battery and the starter motor. The
starter motor is grounded to the cylinder block. With power and ground supplied, the starter motor operates.
Component Parts Location
INFOID:0000000001728576
ALBIA0473GB
1.
IPDM E/R E44, E45, E46
2.
BCM M18 (view with glove box re-
moved)
ALBIA0475GB
STARTING SYSTEM
STR-29
< FUNCTION DIAGNOSIS >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
Component Description
INFOID:0000000001728577
Component part
Description
BCM
BCM sends a starter request signal to the CPU of the IPDM E/R
over the CAN communication lines.
IPDM E/R
CPU inside IPDM E/R operates the starter relay at the request of
the BCM over the CAN communication lines.
Starter motor
The starter motor plunger closes and the motor is supplied with
battery power, which in turn cranks the engine, when the “S” ter-
minal is supplied with electric power.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст