Nissan Tiida C11. Manual — part 1398
TRANSAXLE ASSEMBLY
TM-643
< DISASSEMBLY AND ASSEMBLY >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
28. Remove differential side bearing outer races from clutch hous-
ing and transaxle case using a brass bar.
CAUTION:
Be careful not to damage clutch housing and transaxle
case.
29. Using the drift, with snap rings (1) stretched, press out input
shaft rear bearing and mainshaft rear bearing from transaxle
case.
30. Remove check balls (2) and check ball plugs from transaxle
case.
31. Remove input shaft oil seal and input shaft front bearing from
clutch housing using a suitable drift.
32. Separate oil channel tube at the root.
33. Remove mainshaft front bearing and oil channel from clutch
housing using the valve seat remover.
34. Remove bushings (1) from clutch housing using a suitable
remover.
MCIB0050E
Tool number
A: ST35300000
PCIB1535E
MCIB0044E
Tool number
A: KV111038S0
PCIB1536E
PCIB1537E
TM-644
< DISASSEMBLY AND ASSEMBLY >
[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
35. Remove retaining pin from selector using a pin punch.
36. Remove bushings (1) from transaxle case using a suitable
remover.
37. Remove interlock bolt (1), bushing, spring and striking interlock
from transaxle case.
38. Remove control shaft (1) from transaxle case.
39. Pull out 2 way connector (1) straight from air breather inner tube
(2).
40. Remove air breather inner tube (2) from transaxle case.
PCIB1538E
PCIB1539E
PCIB1540E
PCIB1541E
TRANSAXLE ASSEMBLY
TM-645
< DISASSEMBLY AND ASSEMBLY >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Assembly
INFOID:0000000001381696
1.
Install air breather inner tube (2) to transaxle case.
CAUTION:
Be careful not to damage air breather inner tube.
NOTE:
It is easy to install the air breather inner tube when its end is
closed with tape. Remove the tape after the installation.
2.
Insert 2 way connector (1) straight to air breather inner tube (2).
CAUTION:
Check air breather inner tube for twists after installing.
3.
Apply gear oil to O-ring and install it to control shaft.
CAUTION:
Do not reuse O-ring.
4.
Install control shaft (1) to transaxle case and then install selector
to control shaft. Tighten bolts to the specified torque. Refer to
.
CAUTION:
Be careful with the orientation of selector.
5.
Install selector onto control shaft, and then install retaining pin
(1) to selector.
6.
Install bushings (1) until it is flush with end face of transaxle
case using a suitable drift (A).
PCIB1541E
PCIB1540E
PCIB1645E
PCIB1542E
TM-646
< DISASSEMBLY AND ASSEMBLY >
[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
7.
Install striking interlock, spring, bushing and interlock bolt (1) to
transaxle case, and then tighten interlock bolt to the specified
torque. Refer to
8.
Install bushings (1) until it is flush with end face of clutch housing
using a suitable drift (A).
9.
Install oil channel to clutch housing.
CAUTION:
Do not reuse oil channel.
10. Install mainshaft front bearing until it is flush with end face of
clutch housing using Tool (A).
11. Install input shaft front bearing until it is flush with end face of
clutch housing using Tool (A).
12. Install input shaft oil seal (1) until it is flush with end face of
clutch housing using Tool (A).
PCIB1539E
PCIB1543E
Tool number
A: ST33061000
PCIB1544E
Tool number
A: KV40100900
PCIB1545E
Tool number
A: ST33220000
PCIB1546E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст