Nissan Tiida C11. Manual — part 173
DLK-102
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
TRUNK LID OPENER SWITCH
2.
Check continuity between BCM connector (A) M18 terminal 5
and trunk lid opener switch connector (B) B61 terminal 1.
3.
Check continuity between BCM connector (A) M18 terminal 5 and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair harness or connector.
3.
CHECK TRUNK LID OPENER SWITCH GROUND CIRCUIT
Check continuity between trunk lid opener switch connector and
ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK TRUNK LID OPENER SWITCH
DLK-103, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace trunk lid opener switch.
5.
CHECK INTERMITTENT INCIDENT
Refer to
XX-XX, "*****"
.
>> INSPECTION END.
ALKIA0761ZZ
BCM connector
Terminal
Trunk lid opener switch connector
Terminal
Continuity
M18
5
B61
1
Yes
BCM connector
Terminal
Ground
Continuity
M18
5
No
WIIA1187E
Trunk lid opener switch
Terminal
Ground
Continuity
B61
2
Yes
TRUNK LID OPENER SWITCH
DLK-103
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Component Inspection
INFOID:0000000001507340
1.
CHECK TRUNK LID OPENER SWITCH
1.
Turn ignition switch OFF.
2.
Check continuity between trunk lid opener switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace trunk lid opener switch.
WIIA1186E
Terminal
Condition
Continuity
Trunk lid opener switch
1
2
ON (press and hold)
Yes
OFF (release)
No
DLK-104
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
UNLOCK SENSOR
UNLOCK SENSOR
Description
INFOID:0000000001507333
Detects door lock condition of driver door.
Component Function Check
INFOID:0000000001507334
1.
CHECK FUNCTION
With CONSULT-III
Check unlock sensor DR DOOR STATE in “Data Monitor” mode.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
DLK-104, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000001507335
1.
CHECK UNLOCK SENSOR POWER SUPPLY
Check signal between Intelligent Key unit connector and ground with
oscilloscope.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 2
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key unit and front door lock actuator (driver side) connectors.
Monitor item
Condition
DOOR STAT SW (DR DOOR STATE)
Front door lock (driver side) LOCK : OFF
Front door lock (driver side) UNLOCK : ON
ALKIA0759ZZ
Terminals
Front door lock actuator
(driver side) consition
Voltage (V)
(Approx.)
(+)
(–)
Intelligent Key unit
connector
Terminal
M52
28
Ground
Locked
Unlocked
0
JPMIA0011GB
UNLOCK SENSOR
DLK-105
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between Intelligent Key unit connector (A) M52
terminal 28 and front door lock actuator (driver side) connector
(B) D14 terminal 4.
4.
Check continuity between Intelligent Key unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness between Intelligent Key unit and front door lock actuator (driver side).
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock actuator (driver side) con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK INTELLIGENT KEY UNIT OUTPUT SIGNAL
1.
Connect Intelligent Key unit harness connector.
WIIA1191E
Intelligent Key unit
connector
Terminal
Front door lock actuator (driver side)
connector
Terminal
Continuity
M52
28
D14
4
Yes
Intelligent Key unit connector
Terminal
Ground
Continuity
M52
28
No
WIIA1192E
Front door lock actuator (driver side) con-
nector
Terminal
Ground
Continuity
D14
5
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст