Nissan Tiida C11. Manual — part 773
EXL-90
< ON-VEHICLE REPAIR >
HEADLAMP AIMING CONTROL
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the height sensor bolt closest to the vehicle front first when installing the height sensor.
• The new height sensor must be initialized using Consult III for proper functioning of the automatic headlamp
aiming system.
AUTO LIGHT SYSTEM
EXL-91
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
AUTO LIGHT SYSTEM
Removal and Installation of Light and Rain Sensor
INFOID:0000000001530408
REMOVAL
1.
Remove the rear view mirror. Refer to
MIR-9, "Removal and Installation"
.
2.
Disconnect the light and rain sensor connector.
3.
Remove the light and rain sensor.
INSTALLATION
Installation is in the reverse order of removal.
EXL-92
< ON-VEHICLE REPAIR >
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Bulb Replacement
INFOID:0000000001530538
1.
Remove the side turn signal lamp. Refer to
EXL-92, "Removal and Installation"
2.
Turn bulb socket counterclockwise to unlock it.
3.
Remove the bulb from the socket.
Removal and Installation
INFOID:0000000001530539
REMOVAL
1.
Insert a suitable tool under the side turn signal lamp. While
pushing in on the side turn signal lamp pawl, pull the lamp away
from the front fender as shown.
2.
Disconnect the side turn signal lamp connector and remove the
side turn signal lamp.
NOTE:
Secure the side turn signal lamp harness with tape to prevent
the harness from falling into the front fender.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Install the lamp housing with the bead facing up.
PKIB8657E
PKIB8656E
REAR COMBINATION LAMP
EXL-93
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Bulb Replacement
INFOID:0000000001530525
HATCHBACK
1.
Remove the rear combination lamp. Refer to
EXL-93, "Removal and Installation"
.
2.
Turn the bulb socket counterclockwise to unlock it.
3.
Remove the bulb.
4.
Installation is in the reverse order of removal.
SEDAN
1.
Remove the trunk side finisher. Refer to
INT-35, "Removal and Installation"
2.
Turn the bulb socket counterclockwise to unlock it.
3.
Remove the stop/tail lamp bulb (1), turn signal lamp bulb (2),
and the back-up lamp bulb (3).
4.
Installation is in the reverse order of removal.
Removal and Installation
INFOID:0000000001530526
HATCHBACK
Removal
1.
Remove the rear combination lamp nuts.
2.
Pull the rear combination lamp toward rear of the vehicle to disengage the pawls.
3.
Disconnect the rear combination lamp connector, and remove the rear combination lamp.
Installation
Installation is in the reverse order of removal.
SEDAN
Removal
1.
Remove trunk side finisher, if equipped. Refer to
INT-35, "Removal and Installation"
.
2.
Disconnect the rear combination lamp connector.
3.
Remove the rear combination lamp nuts (1).
4.
Remove the rear combination lamp (2).
5.
Remove the rear combination lamp seal (3).
Installation
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000001530527
Exploded View
PKIC1034E
PKIC1035E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст