Nissan Tiida C11. Manual — part 663
EM-4
DRIVE BELTS . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Inspection and Adjustment . . . . . . . . .
Removal and Installation . . . . . . . . . ...
AIR CLEANER FILTER . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
CAMSHAFT VALVE CLEARANCE . . . . .
Inspection and Adjustment . . . . . . . . .
COMPRESSION PRESSURE . . . . . . ..
Inspection . . . . . . . . . . . . . . . ..
ON-VEHICLE REPAIR . . . . . . . ...
DRIVE BELT AUTO-TENSIONER . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
AIR CLEANER AND AIR DUCT . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
CHARGE AIR COOLER . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
EGR SYSTEM . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
CATALYST . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
TURBOCHARGER . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
EXHAUST MANIFOLD . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
GLOW PLUG . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
VACUUM PUMP . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
INJECTION TUBE AND FUEL INJECTOR . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
OIL PAN . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
HIGH PRESSURE SUPPLY PUMP . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
ROCKER COVER . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
TIMING BELT . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
CAMSHAFT . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
ENGINE ASSEMBLY . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
DISASSEMBLY AND ASSEMBLY . . ...
ENGINE STAND SETTING . . . . . . . ..
Setting . . . . . . . . . . . . . . . . ...
CYLINDER HEAD . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . ..
Cleaning . . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . ..
CYLINDER BLOCK . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
General Specification . . . . . . . . . . ...
Drive Belt . . . . . . . . . . . . . . . ..
Camshaft . . . . . . . . . . . . . . . ...
Cylinder Head . . . . . . . . . . . . . ..
Cylinder Block . . . . . . . . . . . . . ..
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
EM-5
< SYMPTOM DIAGNOSIS >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting - Engine Noise
INFOID:0000000001381371
PBIC3870E
EM-6
< SYMPTOM DIAGNOSIS >
[HR16DE]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
Use the Chart Below to Help You Find the Cause of the Symptom
INFOID:0000000001381372
1.
Locate the area where noise occurs.
2.
Confirm the type of noise.
3.
Specify the operating condition of engine.
4.
Check specified noise source.
If necessary, repair or replace these parts.
A: Closely related
B: Related
C: Sometimes related
—: Not related
Location
of noise
Type of
noise
Operating condition of engine
Source of
noise
Check item
Refer-
ence page
Before
warm-
up
After
warm-
up
When
start-
ing
When
idling
When
racing
While
driving
Top of en-
gine
Rocker
cover
Cylinder
head
Ticking or
clicking
C
A
—
A
B
—
Tappet
noise
Valve clearance
Rattle
C
A
—
A
B
C
Camshaft
bearing
noise
Camshaft journal oil
clearance
Camshaft runout
Crank-
shaft pul-
ley
Cylinder
block
(Side of
engine)
Oil pan
Slap or
knock
—
A
—
B
B
—
Piston pin
noise
Piston to piston pin oil
clearance
Connecting rod small
end clearance
Slap or
rap
A
—
—
B
B
A
Piston
slap noise
Piston to cylinder bore
clearance
Piston ring side clear-
ance
Piston ring end gap
Connecting rod bend
and torsion
Knock
A
B
C
B
B
B
Connect-
ing rod
bearing
noise
Connecting rod small
end clearance
Connecting rod bearing
oil clearance
Knock
A
B
—
A
B
C
Main bear-
ing noise
Main bearing oil clear-
ance
Crankshaft runout
Front of
engine
Front cov-
er
Tapping or
ticking
A
A
—
B
B
B
Timing
chain and
chain ten-
sioner
noise
Timing chain cracks
and wear
Timing chain tensioner
operation
Front of
engine
Squeak-
ing or fizz-
ing
A
B
—
B
—
C
Drive belt
(Sticking
or slip-
ping)
Drive belt deflection
Creaking
A
B
A
B
A
B
Drive belt
(Slipping)
Idler pulley bearing op-
eration
Squall
Creak
A
B
—
B
A
B
Water
pump
noise
Water pump operation
PRECAUTIONS
EM-7
< PRECAUTION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001527642
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000001527633
When performing the procedure after removing cowl top cover, cover
the lower end of windshield.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000001527634
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
PIIB3706J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст