Nissan Tiida C11. Manual — part 713
EM-204
< ON-VEHICLE REPAIR >
[MR18DE]
CYLINDER HEAD
4.
Heat cylinder head to 110
°
to 130
°
C (230
°
to 266
°
F) by soaking
in heated oil (A).
5.
Press valve guide (1) from camshaft side to dimensions as
shown.
CAUTION:
Cylinder head contains heat, when working, wear protective
equipment to avoid getting burned.
6.
Apply reamer finish to valve guide using suitable tool (A).
VALVE SEAT CONTACT
• After confirming that the dimensions of valve guides and valves are within specifications, perform this proce-
dure.
• Apply prussian blue (or white lead) onto contacting surface of valve seat to check the condition of the valve
contact on the surface.
• Check if the contact area band is continuous all around the circum-
ference.
• If not, grind to adjust valve fitting and check again. If the contacting
surface still has NG conditions even after the re-check, replace
valve seat.
VALVE SEAT REPLACEMENT
When valve seat is removed, replace with oversized [0.5 mm (0.020 in)] valve seat.
1.
Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat recess
in cylinder head. Set the machine depth stop to ensure this. Refer to
.
PBIC3214J
2
: Cylinder head
Projection “H”
: 13.35 - 13.65 mm (0.526 - 0.537 in)
PBIC3217J
Standard
: 5.500 - 5.518 mm (0.2165 - 0.2172 in)
PBIC3215J
SBIA0322E
CYLINDER HEAD
EM-205
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Ream cylinder head (1) recess diameter for service valve seat.
• Be sure to ream in circles concentric to the valve guide center.
This will enable valve seat to fit correctly.
3.
Heat cylinder head to 110
°
to 130
°
C (230
°
to 266
°
F) by soaking
in heated oil (A).
4.
Provide valve seats cooled well with dry ice. Press-fit valve seat into cylinder head.
CAUTION:
• Never touch cold valve seats directly.
• Cylinder head contains heat, when working, wear protective equipment to avoid getting burned.
5.
Using valve seat cutter set or valve seat grinder, finish valve
seat to the specified dimensions. For dimensions, refer to
CAUTION:
When using valve seat cutter, firmly grip the cutter handle
with both hands. Then, press on the contacting surface all
around the circumference to cut in a single drive. Improper
pressure on with the cutter or cutting many different times
may result in stage valve seat.
6.
Using compound, grind to adjust valve fitting.
7.
Check again for normal contact.
VALVE SPRING SQUARENESS
• Set try square along the side of valve spring and rotate the spring.
Measure the maximum clearance between the top of valve spring
and try square.
CAUTION:
Never remove valve spring seat from valve spring.
• If it exceeds the limit, replace valve spring (with valve spring seat).
VALVE SPRING DIMENSIONS AND VALVE SPRING PRESSURE LOAD
2
: Valve seat
Oversize [0.5 mm (0.020 in)]
Intake
: 35.200 - 35.227 mm (1.3858 - 1.3869 in)
Exhaust
: 29.200 - 29.227 mm (1.1496 - 1.1507 in)
PBIC3218J
PBIC3214J
SEM934C
Limit: 1.9 mm (0.075 in)
PBIC0080E
EM-206
< ON-VEHICLE REPAIR >
[MR18DE]
CYLINDER HEAD
• Check valve spring pressure with valve spring seat installed at the
specified spring height.
CAUTION:
Never remove valve spring seat from valve spring.
Standard:
• If the installation load or load with valve open is out of the standard, replace valve spring (with valve spring
seat).
SEM113
Items
Intake
Exhaust
Free height
44.90 - 45.10 mm (1.7677 - 1.7755 in)
45.74 - 45.94 mm (1.8007 - 1.8086 in)
Installation height
35.30 mm (1.390 in)
35.30 mm (1.390 in)
Installation load
153 - 173 N (15.6 - 17.6 kg, 34 - 39 lb)
139 - 157 N (14.2 - 16 kg, 10 - 35 lb)
Height during valve open
26.36 mm (1.0377 in)
27.80 mm (1.0944 in)
Load with valve open
335 - 377 N (34.2 - 38.5 kg, 75 - 85 lb)
266 - 297 N (27.1 - 3.03 kg, 60 - 67 lb)
Identification color
White
Orange
ENGINE ASSEMBLY
EM-207
< REMOVAL AND INSTALLATION >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Component
INFOID:0000000001337809
Removal and Installation
INFOID:0000000001337810
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
• Attach proper slingers and bolts described in PARTS CATALOG if engine slingers are not equipped.
CAUTION:
• Always be careful to work safely, avoid forceful or uninstructed operations.
• Do not start working until exhaust system and coolant are cool enough.
• If items or work required are not covered by the engine section, follow the procedures in the applica-
ble sections.
1.
Engine mounting Insulator (RH)
2.
Engine mounting shim (RH) (if equipped)
3.
Engine mounting bracket (RH)
4.
Bracket
5.
Rear torque rod
6.
Engine through bolt
7.
Engine mounting bracket (LH)
8.
Engine mounting insulator (LH)
9.
Torque rod (RH)
A.
Front mark
B.
Silicone lubricant
WBIA0846E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст