Nissan Tiida C11. Manual — part 1406
CONTROL LINKAGE
TM-675
< ON-VEHICLE REPAIR >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Disconnect connectors (A) and then remove bracket (1).
4.
While pressing the lock of the select cable in the direction of the
arrow shown, remove the select cable from the selector lever.
5.
While pressing the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the shifter lever.
6.
While pulling the lock of the select cable in the direction of the
arrow shown, remove the select cable from the cable mounting
bracket.
7.
While pulling the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the cable mounting
bracket.
8.
Remove the control lever knob.
9.
Remove console finisher assembly and the center console
assembly. Refer to
IP-11, "Removal and Installation"
10. Shift the control lever to the neutral position.
11. While pressing the lock of the select cable in the direction of the
arrow shown, remove the select cable from the control device
assembly.
12. While pressing the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the control device
assembly.
13. While pulling the lock of the select cable in the direction of the
arrow shown, remove the select cable from the control device
assembly.
14. While pulling the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the control device
assembly.
15. Remove the control device assembly.
16. Remove the heat plate.
17. Remove the bracket.
JPDIA0240ZZ
JPDIC0066ZZ
JPDIC0067ZZ
JPDIC0066ZZ
JPDIC0067ZZ
TM-676
< ON-VEHICLE REPAIR >
[6MT: RS6F94R]
CONTROL LINKAGE
18. Remove the grommet and then remove the shift cable and select cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Shift the control lever to the neutral position.
• Securely assemble each cable and the selector lever and shifter lever.
• Securely assemble each cable and the cable mounting bracket.
• Securely assemble each cable and the control device assembly.
• Make sure that the claws of grommet are in contact with the floor.
• Be careful about the installation direction and push the control lever knob into the control lever.
CAUTION:
Never reuse control lever knob.
• Tapping work for tapping bolt is not applied to new clutch housing. Do not perform tapping by other than
screwing tapping bolt because tapping is formed by screwing tapping bolt into clutch housing.
CAUTION:
Never reuse tapping bolt.
Install the select cable (the control device assembly side) with the following procedure.
1.
While pulling the lock of the select cable in the direction of the
arrow shown, install the select cable to the control device
assembly.
2.
Slide the lock (1) of the select cable in the direction of the arrow
as shown to pull up the stopper (2) of the select cable.
3.
Install the end of the select cable to the pin of the control device
assembly.
4.
Install the lever stopper pin (1) or a pin [3 mm (0.12 in) dia.] to
the control device assembly.
CAUTION:
Select cable cannot be adjusted accurately without a use of
a lever stopper pin or a pin [3 mm (0.12 in) dia.].
NOTE:
A lever stopper pin is not included in control device assembly.
Therefore, if the control device assembly is not replaced, pre-
pare a pin [3 mm (0.12 in) dia.].
5.
Check that the control lever does not move in the direction of the
select. If it moves, repeat step 3.
6.
Shift the control lever to 4th gear position.
JPDIC0067ZZ
JPDIC0064ZZ
JPDIC0069ZZ
CONTROL LINKAGE
TM-677
< ON-VEHICLE REPAIR >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
With the stopper (1) of the select cable pressed into all the way,
slide lock (2) of the select cable all the way in the direction of the
arrow.
8.
Remove the lever stopper pin or a pin [3 mm (0.12 in) dia.] from
the control device assembly.
9.
Shift the control lever to each gear position to check that there is
no binding. If any, repeat step 3.
Inspection
INFOID:0000000001381640
After installing, confirm the following items:
• When the control lever is shifted to 1st-2nd side and 5th-6th side, confirm the control lever returns to neutral
position smoothly.
• When the control lever is shifted to each position, make sure there is no binding or disconnection in each
boot.
JPDIC0065ZZ
TM-678
< ON-VEHICLE REPAIR >
[6MT: RS6F94R]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000001381641
MR18DE ENGINE MODELS
K9K ENGINE MODELS
Removal and Installation
INFOID:0000000001381642
REMOVAL
SCIA7629E
1.
Air cleaner case
2.
Air breather hose
3.
Air duct
4.
Clip
5.
Transaxle assembly
⇐
Two way connector
ALDIA0192ZZ
1.
Air duct
2.
Transaxle assembly
3.
Air breather hose
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст