Nissan Tiida C11. Manual — part 1405
PREPARATION
TM-671
< PREPARATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Drift
a: 17 mm (0.67 in) dia.
• Installing bushing
• Installing shifter lever oil seal
• Installing selector lever oil seal
Drift
a: 35 mm (1.38 in) dia.
b: 25 mm (0.98 in) dia.
Installing input shaft front bearing
Drift
a: 24 mm (0.94 in) dia.
Removing input shaft rear bearing
Drift
a: 43 mm (1.69 in) dia.
• Removing differential side bearing inner
race (transaxle case side)
• Installing input shaft rear bearing
Drift
a: 45 mm (1.77 in) dia.
b: 39 mm (1.54 in) dia.
Installing differential side bearing inner race
(clutch housing side)
Drift
a: 52 mm (2.05 in) dia.
b: 45 mm (1.77 in) dia.
Installing differential side bearing inner race
(transaxle case side)
Tool name
Description
S-NT063
S-NT065
PCIB1779E
NT109
S-NT474
S-NT474
TM-672
< ON-VEHICLE MAINTENANCE >
[6MT: RS6F94R]
GEAR OIL
ON-VEHICLE MAINTENANCE
GEAR OIL
Exploded View
INFOID:0000000001381632
Draining
INFOID:0000000001381633
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and then drain oil.
3.
Set a new gasket on drain plug (1) and install it to transaxle and
tighten drain plug to the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Refilling
INFOID:0000000001381634
1.
Remove filler plug (1). Fill with new oil until oil level reaches the
specified limit near filler plug hole as shown.
2.
After refilling oil, check oil level.
3.
Set a new gasket on filler plug (1), then install it to transaxle and
tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
Inspection
INFOID:0000000001381635
LEAKAGE
Make sure that oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Do not start engine while checking oil level.
2.
Set a new gasket on filler plug (1) and install it to the transaxle
case.
CAUTION:
Do not reuse gasket.
3.
Tighten filler plug to the specified torque. Refer to
SCIA7622E
Oil grade and capacity
: Refer to
.
SCIA7623E
SCIA7623E
SIDE OIL SEAL
TM-673
< ON-VEHICLE REPAIR >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE REPAIR
SIDE OIL SEAL
Exploded View
INFOID:0000000001381636
Removal and Installation
INFOID:0000000001381637
REMOVAL
1.
Remove front drive shafts. Refer to
FAX-10, "Removal and Installation (Left Side)"
and Installation (Right Side)"
.
2.
Remove differential side oil seals (1) using a suitable tool.
CAUTION:
Do not damage transaxle case and clutch housing.
INSTALLATION
Installation is in the reverse order of removal.
• Install differential side oil seals (1) to transaxle case side (B) and
clutch housing side (C) using Tool (A).
CAUTION:
• Do not reuse differential side oil seal.
• When installing, never incline differential side oil seal.
• Do not damage clutch housing and transaxle case.
• Check oil level and oil leakage after installation. Refer to
SCIA7625E
Tool number
: KV38100300
Dimension “L
1
”
: 1.2 - 1.8 mm (0.047 - 0.071 in)
Dimension “L
2
”
: 2.7 - 3.3 mm (0.106 - 0.130 in)
JPDIC0120ZZ
TM-674
< ON-VEHICLE REPAIR >
[6MT: RS6F94R]
CONTROL LINKAGE
CONTROL LINKAGE
Exploded View
INFOID:0000000001381638
Removal and Installation
INFOID:0000000001381639
REMOVAL
1.
Remove the air cleaner and air duct. Refer to
EM-154, "Removal and Installation"
(MR18DE) or
(K9K).
2.
Remove the battery. Refer to
PG-6, "Removal and Installation"
1.
Bracket
2.
Shift cable
3.
Selector lever
4.
Shifter lever
5.
Tapping bolt
6.
Cable mounting bracket
7.
Select cable
8.
Grommet
9.
Control device assembly
10. Control lever
11.
Control lever knob
JPDIC0058GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст