Nissan Tiida C11. Manual — part 696
EM-136
< PRECAUTION >
[MR18DE]
PRECAUTIONS
• The torque value for these parts are for a preliminary step.
• Ensure thread and seat surfaces are clean and coated with engine oil.
Precaution for Liquid Gasket
INFOID:0000000001337771
REMOVAL OF LIQUID GASKET SEALING
• After removing the bolts and nuts, separate the mating surface and
remove the sealant using Tool.
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to
lightly tap (1) the cutter where the RTV Silicone Sealant is applied.
Use a plastic hammer to slide the cutter (2) by tapping on the side.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating sur-
faces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old Silicone RTV Sealant adhering
to the gasket application surface and the mating surface.
• Remove the sealant completely from the groove of the gasket
application surface, bolts, and bolt holes.
2.
Thoroughly clean the gasket application surface and the mating
surface and remove adhering moisture, grease and foreign
materials.
3.
Attach the sealant tube to the tube presser.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-27, "Recommended Chemical Products and Sealants"
.
4.
Apply the sealant without breaks to the specified location using
Tool.
• If there is a groove for the sealant application, apply the seal-
ant to the groove.
• As for the bolt holes, normally apply the sealant inside the
holes. If specified, it should be applied outside the holes. Make
sure to read the text of this manual.
• Within five minutes of the sealant application, install the mat-
ing component.
• If the sealant protrudes, wipe it off immediately.
• Do not retighten after the installation.
• After 30 minutes or more have passed from the installation, fill
the engine with the specified oil and coolant. Refer to
CAUTION:
Tool number
: KV10111100 (J-37228)
WBIA0566E
PBIC0003E
Tool number
WS39930000 (
–
)
WBIA0567E
SEM159F
PRECAUTIONS
EM-137
< PRECAUTION >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Follow all specific instructions in this manual.
EM-138
< PREPARATION >
[MR18DE]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000001337772
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV10111100
(J-37228)
Seal cutter
Removing steel oil pan and rear timing
chain case
KV10112100
(BT-8653-A)
Angle wrench
Tightening bolts for bearing cap, cylinder
head, etc.
KV10107902
(J-38959)
Valve oil seal puller
Removing valve oil seal
EM03470000
(J-8037)
Piston ring compressor
Installing piston assembly into cylinder
bore
KV101092S0
(J-26336-B)
Valve spring compressor
1 KV10109210
(J-26336-20)
Attachment
2 KV10109220
(
—
)
3. KV10109230
Adapter (M8)
Disassembling and assembling valve
mechanism
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
NT046
NT014
S-NT011
NT044
NT718
NT052
PREPARATION
EM-139
< PREPARATION >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ST16610001
(J-23907)
Pilot bushing puller
Removing crankshaft pilot bushing
KV11103000
(—)
Pulley puller
Removing crankshaft pulley
KV991J0050
(J-44626)
Air fuel sensor Socket
Loosening or tightening air fuel ratio A/F
sensor
a: 22 mm (0.87 in)
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening rear heated oxy-
gen sensor
a: 22 mm (0.87 in)
KV11105210
(J-44716)
Stopper plate
Securing driveplate and flywheel
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A.
a: 20 (0.79) dia.
b: 13 (0.51) dia.
c: 10.3 (0.406) dia.
d: 8 (0.31) dia.
e: 10.7 (0.421)
f: 5 (0.20)
KV10115801
(
—
)
Oil filter wrench
Removing and installing oil filter
a: 64.3 mm (2.531 in)
Tool number
(Kent-Moore No.)
Tool name
Description
NT045
NT676
LBIA0444E
NT636
ZZA0009D
S-NT603
S-NT375
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст