Nissan Tiida C11. Manual — part 1296
DISASSEMBLY
TM-235
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
47. Remove output shaft, output gear and reduction gear according to the following procedures.
a.
Set manual shaft in “P” position to fix idler gear and output gear.
b.
Unlock both idler gear and output gear lock nuts using a pin punch.
c.
Remove idler gear and output gear lock nuts.
d.
Remove idler gear (2) and output gear (1) using Tool A.
e.
Remove reduction pinion gear and output shaft from transaxle
case.
f.
Remove reduction pinion gear adjusting shim (1) from reduction
pinion gear (2).
g.
Remove output gear adjusting spacer (3) from output shaft (4).
48. Remove bearing retainer fitting bolts, and then remove bearing
retainer (1) from transaxle case.
SAT704D
Tool number:
ST27180001
SCIA6991E
SCIA5902J
SCIA5909J
TM-236
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
DISASSEMBLY
49. Remove return spring (2) from parking shaft (3) suitable tool.
(1): Parking pawl
• Inspect return spring (2), and replace if damaged or worn.
50. Draw out parking shaft (1), and then remove parking pawl (2)
from transaxle case.
• Inspect parking shaft (1) and parking pawl (2), and replace
if damaged or worn.
51. Remove parking actuator support (1) from transaxle case.
• Inspect parking actuator support (1), and replace if dam-
aged or worn.
52. Remove snap ring from transaxle case using suitable tool.
53. Remove governor cap from transaxle case.
54. Remove O-ring from governor cap.
55. Remove LH differential side oil seal from transaxle case using
suitable tool.
CAUTION:
Do not scratch transaxle case.
SCIA6996E
SCIA6997E
SCIA6998E
ATM0076D
REPAIR FOR COMPONENT PARTS
TM-237
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REPAIR FOR COMPONENT PARTS
Manual Shaft
INFOID:0000000001730983
COMPONENTS
REMOVAL
1.
Remove detent spring from transaxle case.
2.
Drive out retaining pin of manual plate using suitable tool.
1.
Manual shaft oil seal
2.
Parking rod
3.
Retaining pin
4.
Parking rod plate
5.
Retaining pin
6.
Manual plate
7.
Manual shaft
8.
Detent spring
9.
Retaining pin
SCIA5907J
SAT313G
SAT076D
TM-238
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
3.
Pull out retaining pin (2) of parking rod plate (1) using suitable
tool.
4.
Pull out retaining pin (1) of manual shaft using suitable tool.
5.
Remove parking rod plate (with parking rod) (3) from manual
shaft (1).
6.
Remove parking rod from parking rod plate (3).
7.
Remove manual plate (2) from manual shaft (1).
8.
Draw out manual shaft (1) from transaxle case.
9.
Remove manual shaft oil seal from transaxle case using suitable
tool.
CAUTION:
Do not scratch transaxle case.
INSPECTION
Check component parts, and replace if damaged or worn.
INSTALLATION
SCIA5806J
SCIA6514J
SCIA7005E
SAT080D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст