Nissan Frontier D40. Manual — part 765
POWER SUPPLY AND GROUND CIRCUIT
INL-15
< COMPONENT DIAGNOSIS >
[WITH POWER DOOR LOCKS]
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
COMPONENT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis Procedure
INFOID:0000000005550754
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit.
NO
>> GO TO 2
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM.
3.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Terminal No.
Signal name
Fuses and fusible link No.
57
Battery power supply
18 (10A)
70
G (50A)
11
Ignition ACC or ON
4 (10A)
38
Ignition ON or START
1 (10A)
Connector
Terminals
Power
source
Condition
Voltage (V) (Ap-
prox.)
(+)
(-)
M18
11
Ground
ACC
power
supply
Ignition
switch
ACC or
ON
Battery voltage
38
Ground
Ignition
power
supply
Ignition
switch ON
or START
Battery voltage
M20
57
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
70
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
LIIA2415E
INL-16
< COMPONENT DIAGNOSIS >
[WITH POWER DOOR LOCKS]
POWER SUPPLY AND GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair or replace harness.
BCM
Ground
Continuity
Connector
Terminal
M20
67
Yes
LIIA0915E
BATTERY SAVER OUTPUT/POWER SUPPLY CIRCUIT
INL-17
< COMPONENT DIAGNOSIS >
[WITH POWER DOOR LOCKS]
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
BATTERY SAVER OUTPUT/POWER SUPPLY CIRCUIT
Description
INFOID:0000000005272811
Provides the battery saver output/power supply. Also cuts the power supply when the interior room lamp bat-
tery saver is activating.
Component Function Check
INFOID:0000000005272812
1.
CHECK BATTERY SAVER OUTPUT/POWER SUPPLY FUNCTION
CONSULT-III
1.
Turn ignition switch ON.
2.
Turn each interior room lamp ON.
-
Front room/map lamp assembly (if equipped)
-
Vanity lamps (if equipped)
-
Room lamp 2nd row
3.
Select “BATTERY SAVER” of BCM (BATTERY SAVER) active test item.
4.
While operating the test item, check that each interior room lamp turns ON/OFF.
Is the inspection result normal?
YES
>> Battery saver output/power supply circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000005272813
Regarding Wiring Diagram information, refer to
.
1.
CHECK BATTERY SAVER OUTPUT/POWER SUPPLY OUTPUT
CONSULT-III
1.
Turn ignition switch ON.
2.
Select “BATTERY SAVER” of BCM (BATTERY SAVER) active
test item.
3.
While operating the test item, check voltage between BCM con-
nector M20 terminal 56 and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Replace BCM. Refer to
BCS-54, "Removal and Installation"
2.
CHECK BATTERY SAVER OUTPUT/POWER SUPPLY OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the following connectors.
-
BCM M20
-
Ignition keyhole illumination (if equipped)
-
Front room/map lamp assembly (if equipped)
-
Vanity lamp LH (if equipped)
-
Vanity lamp RH (if equipped)
-
Room lamp 2nd row
OFF
: Interior room lamp OFF
ON
: Interior room lamp ON
(+)
(-)
Test item
Voltage
Connector
Terminal
BATTERY SAVER
M20
56
Ground
OFF
0V
ON
Battery voltage
ALLIA0408GB
INL-18
< COMPONENT DIAGNOSIS >
[WITH POWER DOOR LOCKS]
BATTERY SAVER OUTPUT/POWER SUPPLY CIRCUIT
3.
Check continuity between BCM connector and each interior room lamp connector.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair the harness or connectors.
3.
CHECK BATTERY SAVER OUTPUT/POWER SUPPLY SHORT CIRCUIT
Check continuity between BCM connector M20 terminal 56 and
ground.
Is the inspection result normal?
YES
>> Replace the interior room lamp. Refer to
.
NO
>> Repair the harness or connectors.
BCM
Each interior room lamp
Continuity
Connector
Terminal
Connector
Terminal
M20
56
Ignition keyhole illumination (if equipped)
M150
1
Yes
Front room/map lamp assembly (if equipped)
R9
1
Vanity lamp LH (if equipped)
B80
1
Vanity lamp RH (if equipped)
B81
1
Room lamp 2nd row
R10
2
Connector
Terminal
—
Continuity
M20
56
Ground
No
ALLIA0409GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст