Nissan Frontier D40. Manual — part 764
DIAGNOSIS SYSTEM (BCM)
INL-11
< FUNCTION DIAGNOSIS >
[WITH POWER DOOR LOCKS]
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000005550744
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
INT LAMP
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM. Refer to
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION
The BCM part number is displayed.
CONFIGURATION
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
BCM
BCM
×
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioner
AIR CONDITONER
×
Combination switch
COMB SW
×
Immobilizer
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP (retained accessory power)
RETAINED PWR
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS (tire pressure monitoring sys-
tem)
AIR PRESSURE MONITOR
×
×
×
Panic alarm system
PANIC ALARM
×
INL-12
< FUNCTION DIAGNOSIS >
[WITH POWER DOOR LOCKS]
DIAGNOSIS SYSTEM (BCM)
INT LAMP : CONSULT-III Function (BCM - INT LAMP)
INFOID:0000000005550745
WORK SUPPORT
* : Initial setting
DATA MONITOR
JPLIA0093GB
Work Item
Setting item
Setting
SET I/L D-UNLCK INTCON
ON*
With the interior room lamp timer function
OFF
Without the interior room lamp timer function
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2
1 sec.
MODE 3
2 sec.
MODE 4*
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judges from IGN signal (ignition power supply)
KEY ON SW [ON/OFF]
The switch status input from key switch
DOOR SW-DR [ON/OFF]
Indicates condition of front door switch (all) and rear door switch upper and lower
(king cab) LH
DOOR SW-AS [ON/OFF]
Indicates condition of front door switch (all) and rear door switch upper and lower
(king cab) RH
DOOR SW-RR [ON/OFF]
Indicates condition of rear door switch RH (crew cab)
DOOR SW- RL [ON/OFF]
Indicates condition of rear door switch LH (crew cab)
KEY CYL LK-SW [ON/OFF]
Lock switch status input from door lock and unlock switch
DIAGNOSIS SYSTEM (BCM)
INL-13
< FUNCTION DIAGNOSIS >
[WITH POWER DOOR LOCKS]
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000005550746
WORK SUPPORT
*: Initial setting
DATA MONITOR
ACTIVE TEST
KEY CYL UN-SW [ON/OFF]
Lock switch status input from door lock and unlock switch
CDL LOCK SW [ON/OFF]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW [ON/OFF]
Unlock switch status input from door lock and unlock switch
KEYLESS LOCK [ON/OFF]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
KEYLESS UNLOCK [ON/OFF]
Unlock signal status received from remote keyless entry receiver (integrated in the
BCM)
Monitor Item
[Unit]
Description
Test Item
Operation
Description
IGN ILLUM
ON
Outputs the ignition keyhole illumination control signal to turn the ignition keyhole il-
lumination lamp ON.
OFF
Stops the ignition keyhole illumination control signal to turn the ignition keyhole illu-
mination lamp OFF.
INT LAMP
ON
Outputs the interior room lamp control signal to turn the interior room lamps ON.
OFF
Stops the interior room lamp control signal to turn the interior room lamps OFF.
Work Item
Setting Item
Setting
ROOM LAMP TIMER SET
MODE 1*
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
MODE 3
10 min.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judges from IGN signal (ignition power supply)
KEY ON SW [ON/OFF]
The switch status input from key switch
DOOR SW-DR [ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS [ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR [ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL [ON/OFF]
The switch status input from rear door switch LH
KEY CYL LK-SW [ON/OFF]
Lock switch status input from door key cylinder switch
KEY CYL UN-SW [ON/OFF]
Unlock switch status input from door key cylinder switch
CDL LOCK SW [ON/OFF]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW [ON/OFF]
Unlock switch status input from door lock and unlock switch
KEYLESS LOCK [ON/OFF]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
KEYLESS UNLOCK [ON/OFF]
Unlock signal status received from remote keyless entry receiver (integrated in the
BCM)
INL-14
< FUNCTION DIAGNOSIS >
[WITH POWER DOOR LOCKS]
DIAGNOSIS SYSTEM (BCM)
*: Each lamp switch is in ON position.
Test Item
Operation
Description
BATTERY SAVER
OFF
Cuts the interior room lamp power supply to turn interior room lamps OFF.
ON
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст