Nissan Frontier D40. Manual — part 801
INSTRUMENT PANEL ASSEMBLY
IP-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Removal and Installation
INFOID:0000000005272874
INSTRUMENT PANEL
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery terminals, then wait at least 3
minutes.
1.
Disconnect the negative and positive battery negative terminals.
2.
Remove the center console. Refer to CENTER CONSOLE in this section.
3.
Remove the combination meter. Refer to
MWI-95, "Removal and Installation"
4.
Remove front pillar upper finisher. Refer to
INT-18, "Removal and Installation"
5.
Remove audio unit. Refer to
AV-28, "Removal and Installation"
6.
Remove cluster lid D. Refer to CLUSTER LID D (BASE or PUSH TYPE) in this section.
7.
Remove the passenger air bag module. Refer to
SR-8, "Removal and Installation"
8.
Remove the instrument stay RH/LH bolts.
9.
Remove instrument panel and pad assembly.
• Disconnect all remaining harnesses.
Installation
Installation is in the reverse order of removal.
CLUSTER LID C - BASE
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery terminals, then wait at least 3
minutes.
1.
Remove tray mat, then release the clips and remove storage tray.
2.
Remove the screw, then release the clips and remove cluster lid C from instrument panel and pad assem-
bly.
3.
Disconnect harness connectors and remove cluster lid C.
Installation
16.
Center ventilator assembly RH/LH
17.
Cluster lid D
18.
Audio unit
19.
Lower glove box latch assembly
20.
Lower glove box assembly
21.
Fuse block cover
22.
Lower glove box damper assembly
23.
Instrument lower panel RH
24.
Upper glove box door
25.
Upper glove box lid
27.
Instrument panel and pad assembly 28.
Passenger air bag module
29.
Sensor cover
ALJIA0462ZZ
1.
Tray mat
2.
Storage tray
3.
Cluster lid C
Pawl
Metal clip
IP-12
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
Installation is in the reverse order of removal.
CLUSTER LID C - PUSH TYPE
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery terminals, then wait at least 3
minutes.
1.
Release the clips and remove storage tray.
2.
Remove the cluster lid C screws, then release the clips.
3.
Disconnect harness connectors and remove cluster lid C.
Installation
Installation is in the reverse order of removal.
CLUSTER LID D - BASE
ALJIA0458ZZ
1.
Storage tray
2.
Cluster lid C
Pawl
Metal clip
ALJIA0464ZZ
ALJIA0463ZZ
INSTRUMENT PANEL ASSEMBLY
IP-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Removal
1.
Remove center console. Refer to CENTER CONSOLE in this section.
2.
Remove lower instrument panel LH. Refer to LOWER INSTRUMENT PANEL LH in this section.
3.
Remove lower instrument panel RH and lower glove box. Refer to LOWER INSTRUMENT PANEL RH
AND LOWER GLOVE BOX in this section.
4.
Remove cluster lid C. Refer to CLUSTER LID C in this section.
5.
Remove the screws, then disconnect the harness connectors and remove cluster lid D.
Installation
Installation is in the reverse order of removal.
CLUSTER LID D - PUSH TYPE
Removal
1.
Remove center console. Refer to CENTER CONSOLE in this section.
2.
Remove lower instrument panel LH. Refer to LOWER INSTRUMENT PANEL LH in this section.
3.
Remove lower instrument panel RH and lower glove box. Refer to LOWER INSTRUMENT PANEL RH
AND LOWER GLOVE BOX in this section.
4.
Remove cluster lid C. Refer to CLUSTER LID C in this section.
5.
Remove the screws, then disconnect the harness connectors and remove cluster lid D.
Installation
Installation is in the reverse order of removal.
LOWER INSTRUMENT PANEL LH
Removal
1.
Remove front pillar lower finisher. Refer to
INT-18, "Removal and Installation"
.
2.
Remove lower instrument panel LH screws, using power tool.
3.
Pull rearward to release lower instrument panel LH.
4.
Disconnect lower instrument panel LH harness connectors.
1.
Cluster lid D
A.
Cluster lid D screw
ALJIA0459ZZ
1.
Cluster lid D
A.
Cluster lid D screw
LIIA1744E
IP-14
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
Installation
Installation is in the reverse order of removal.
CLUSTER LID A
Removal
1.
Remove front pillar upper finisher. Refer to
INT-18, "Removal and Installation"
.
2.
Remove lower instrument panel LH. Refer to
IP-11, "Removal and Installation"
3.
Remove steering lock escutcheon.
4.
Remove the screws and clips, then lift cluster lid A rearward in vehicle away from the instrument panel.
Installation
Installation is in the reverse order of removal.
STEERING COLUMN COVER
Removal
1.
Partially remove driver door weatherstrip and set aside.
2.
Remove front pillar lower finisher. Refer to
INT-18, "Removal and Installation"
.
3.
Remove lower intstrument panel LH. Refer to LOWER INSTRUMET PANEL LH in this section.
4.
Remove the steering column cover screws, then remove both the upper and lower portions of the steering
column cover.
Installation
Installation is in the reverse order of removal.
A/T FINISHER
Removal
1.
Remove cup holder finisher.
2.
Pull up to release clips, then remove the A/T finisher.
ALJIA0460ZZ
1.
Combination meter
2.
Cluster lid A
3.
Ignition key lamp assembly
4.
Steering lock escutcheon
Metal clip
LIIA1941E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст