Nissan Frontier D40. Manual — part 247
DIAGNOSIS AND REPAIR WORKFLOW
DLN-9
< BASIC INSPECTION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
>> GO TO 4
4.
SYMPTOM
Check for symptoms. Refer to
>> GO TO 5
5.
MALFUNCTIONING PARTS
Repair or replace the applicable parts.
>> GO TO 6
6.
SYSTEM OPERATION
Check system operation.
>> GO TO 7
7.
SELF-DIAGNOSIS
Perform self-diagnosis.
Are any DTC's displayed?
YES
>> GO TO 5
NO
>> Inspection End
DLN-10
< FUNCTION DIAGNOSIS >
[TRANSFER: TX15B]
4WD SYSTEM
FUNCTION DIAGNOSIS
4WD SYSTEM
System Diagram
INFOID:0000000005275405
COMPONENT DESCRIPTION
SDIA3416E
Components
Function
Transfer control unit
Controls transfer control device and controls shifts between 2WD/4WD and 4H/4LO.
Transfer control device
Integrates actuator motor and actuator position switch.
Actuator motor
Moves shift rods when signaled by transfer control unit.
Actuator position switch
Detects actuator motor position.
Wait detection switch
Detects if transfer case is in 4WD.
4LO switch
Detects if transfer case is in 4LO.
ATP switch (A/T models)
Detects if transfer case is in neutral.
4WD shift switch
Allows driver to select from 2WD/4WD and 4H/4LO.
4WD warning lamp
• Illuminates if malfunction is detected in 4WD system.
• Flashes (1 flash / 2 seconds) if rotation difference of front wheels and rear wheels is large.
ATP warning lamp (A/T models)
Indicates that A/T parking mechanism does not operate when A/T selector lever is in “P” position be-
cause transfer case is in neutral.
4WD shift indicator lamp
Displays driving range selected by 4WD shift switch.
4LO indicator lamp
Displays 4LO range.
PNP switch
(M/T models)
Detects if manual transmission is under neutral condition.
ABS actuator and electric unit
(control unit)
Transmits the following signals via CAN communication to transfer control unit.
• Vehicle speed signal
• Stop lamp switch signal (brake signal)
4WD SYSTEM
DLN-11
< FUNCTION DIAGNOSIS >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
System Description
INFOID:0000000005275406
TRANSFER CONTROL DEVICE
Integrates actuator motor and actuator position switch.
Actuator Motor
Moves shift rods when signaled by transfer control unit.
Actuator Position Switch
Detects actuator motor position and then sends signal to transfer control unit.
WAIT DETECTION SWITCH
Detects if transfer case is in 4WD by the 2-4 shift fork position.
NOTE:
If 4WD shift switch is switched to 4H or 4LO and the transfer case is not in 4WD completely, the wait detection
system will operate.
4LO SWITCH
4LO switch detects if the transfer case is in 4LO by the position of the L-H shift fork.
ATP SWITCH (A/T MODELS)
ATP switch detects if transfer case is in neutral by the position of the L-H shift fork.
NOTE:
Transfer case may be in neutral when shifting between 4H-4LO.
PNP SWITCH (M/T models)
PNP switch detects if manual transmission is under neutral condition.
TRANSFER CONTROL UNIT
• Transfer control unit controls transfer control device and it directs shifts from 4H-4LO and 2WD-4WD.
• Self-diagnosis can be done.
TRANSFER SHIFT HIGH AND LOW RELAYS
Transfer shift high and low relays apply power supply to transfer control device (actuator motor).
TRANSFER SHUT OFF RELAYS
Transfer shut off relays 1 and 2 apply power supply to transfer control unit.
4WD SHIFT SWITCH AND INDICATOR LAMP
TCM (A/T models)
Transmits the following signal via CAN communication to transfer control unit.
• Output shaft revolution signal
• A/T position indicator signal (transmission range switch signal)
ECM
Transmits engine speed signal via CAN communication to transfer control unit.
Components
Function
DLN-12
< FUNCTION DIAGNOSIS >
[TRANSFER: TX15B]
4WD SYSTEM
4WD Shift Switch
4WD shift switch is able to select from 2WD, 4H or 4LO.
4WD Shift Indicator Lamp
• Displays driving conditions selected by the 4WD shift switch while engine is running. When the 4WD warn-
ing lamp is turned on, all 4WD shift indicator lamps will turn off.
• Turns ON when ignition switch is turned ON, for purpose of lamp check. Turns OFF approximately for 1 sec-
ond after the engine starts if system is normal.
4LO Indicator Lamp
• Displays 4LO while engine is running. 4LO indicator lamp flashes if transfer gear does not shift completely
into 4H
⇔
4LO. In this condition, the transfer case may be in neutral and the A/T parking mechanism may not
operate.
• Turns ON when ignition switch is turned ON, for purpose of lamp check. Turns OFF approximately for 1 sec-
ond after the engine starts if system is normal.
4WD WARNING LAMP
Turns on or flashes when there is a malfunction in 4WD system.
Also turns on when ignition switch is turned ON, for purpose of lamp check. Turns OFF approximately for 1
second after the engine starts if system is normal.
4WD Warning Lamp Indication
ATP WARNING LAMP (A/T MODELS)
SDIA3290E
Condition
4WD warning lamp
System normal
OFF
Lamp check
Turns ON when ignition switch is turned ON.
Turns OFF after engine start.
4WD system malfunction
ON
During self-diagnosis
Flashes malfunction mode.
Large difference in diameter of front/
rear tires
Flashes slow (1 flash / 2 seconds)
(Continues to flash until the ignition switch is turned OFF)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст