Nissan Frontier D40. Manual — part 123
BRC-190
< BASIC INSPECTION >
[TYPE 3]
INSPECTION AND ADJUSTMENT
>> GO TO 2
2.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1.
On the CONSULT-III screen, touch “WORK SUPPORT” and “ST ANG SEN ADJUSTMENT” in order.
2.
Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle sensor.
3.
After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4.
Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.
CHECK DATA MONITOR
1.
Run vehicle with front wheels in straight-ahead position, then stop.
2.
Select “DATA MONITOR”. Then make sure “STR ANGLE SIG” is within 0
±
2.5
°
.
Is the steering angle within the specified range?
YES
>> GO TO 4
NO
>> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1
4.
ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
• ABS actuator and electric unit (control unit): Refer to
BRC-212, "CONSULT-III Function (ABS)"
.
• ECM: Refer to
EC-528, "CONSULT-III Function (ENGINE)"
Are the memories erased?
YES
>> Inspection End
NO
>> Check the items indicated by the self-diagnosis.
CALIBRATION OF DECEL G SENSOR
CALIBRATION OF DECEL G SENSOR : Description
INFOID:0000000005275226
Refer to the table below to determine if calibration of the decel G sensor is required.
×
: Required –: Not required
CALIBRATION OF DECEL G SENSOR : Special Repair Requirement
INFOID:0000000005275227
CALIBRATION OF DECEL G SENSOR
CAUTION:
To calibrate the decel G sensor, make sure to use CONSULT-III
Situation
Calibration of decel G sensor
Removing/Installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/Installing steering angle sensor
×
Replacing steering angle sensor
×
Removing/Installing steering components
×
Replacing steering components
×
Removing/Installing suspension components
×
Replacing suspension components
×
Change tires to new ones
—
Tire rotation
—
Adjusting wheel alignment
×
INSPECTION AND ADJUSTMENT
BRC-191
< BASIC INSPECTION >
[TYPE 3]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
(Calibration cannot be done without CONSULT-III)
1.
ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2
2.
PERFORM CALIBRATION OF DECEL G SENSOR
1.
On the CONSULT-III screen, touch “WORK SUPPORT” and “DECEL G SEN CALIBRATION” in order.
2.
Touch “START”.
3.
After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4.
Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.
CHECK DATA MONITOR
1.
Run vehicle with front wheels in straight-ahead position, then stop.
2.
Select “DATA MONITOR”. Then make sure “DECEL G SEN” is within
±
0.08G.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Perform calibration of decel G sensor again, GO TO 1
4.
ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
• ABS actuator and electric unit (control unit): Refer to
BRC-212, "CONSULT-III Function (ABS)"
• ECM: Refer to
EC-528, "CONSULT-III Function (ENGINE)"
Are the memories erased?
YES
>> Inspection End
NO
>> Check the items indicated by the self-diagnosis.
BRC-192
< FUNCTION DIAGNOSIS >
[TYPE 3]
APPLICATION NOTICE
FUNCTION DIAGNOSIS
APPLICATION NOTICE
Application Notice
INFOID:0000000005548021
Service information
Remarks
TYPE 1
ABS
TYPE 2
VDC/TCS/ABS
TYPE 3
HILL DESCENT CONTROL/HILL START ASSIST/VDC/TCS/ABS
VDC
BRC-193
< FUNCTION DIAGNOSIS >
[TYPE 3]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
VDC
System Diagram
INFOID:0000000005275229
HYDRAULIC CIRCUIT DIAGRAM
AWFIA0489GB
AWFIA0201GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст