Nissan Frontier D40. Manual — part 1156
WHEEL AND TIRE ASSEMBLY
WT-47
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
4.
After the wheel and tire rotation, retighten the wheel nuts after the vehicle has been driven for 1,000 km
(600 miles), and also after any wheel and tire has been installed, such as after repairing a flat tire.
WT-48
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
Transmitter (Pressure Sensor)
INFOID:0000000005275762
REMOVAL
1.
Remove wheel and tire using power tool.
2.
Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
3.
Gently bounce tire so that transmitter falls to bottom of tire.
Place wheel and tire assembly on tire changing machine and
break both tire beads. Ensure that the transmitter remains at the
bottom of the tire while breaking the bead.
4.
Turn tire so that valve hole is at bottom, and gently bounce the
tire to ensure transmitter is near valve hole. Carefully lift tire onto
turntable and position valve hole (and transmitter) 270 degrees
from mounting/dismounting head.
5.
Lubricate tire well, and remove top side of tire. Reach inside the
tire and remove the transmitter.
6.
Remove the second side of the tire as normal.
INSTALLATION
1.
Place first side of tire onto rim.
2.
Apply suitable silicone lubricant to new transmitter seal then
install seal on transmitter.
NOTE:
Always replace the seal after every disassembly.
3.
Mount transmitter on wheel rim and tighten nut.
NOTE:
Make sure no burrs exist in the valve stem hole of the wheel.
SEIA0047E
WEIA0046E
SEIA0049E
Transmitter nut
tightening torque
: 7.7 N·m (0.79 kg-m, 68 in-lb)
WEIA0137E
REMOVAL AND INSTALLATION
WT-49
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
4.
Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degrees from mounting/dismounting head.
NOTE:
Do not touch transmitter with mounting head.
5.
Lubricate tire well, and install second side of tire as normal.
Ensure that tire does not rotate relative to rim.
6.
Inflate tire and balance the wheel and tire assembly. Refer to
7.
Install wheel and tire assembly in appropriate wheel position on
vehicle.
NOTE:
If replacing the transmitter, then transmitter wake up operation
must be performed. Refer to
WT-5, "Transmitter Wake Up Operation"
WEIA0046E
WT-50
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000005275763
Tire
INFOID:0000000005275764
Unit: kPa (kg/cm
2
, psi)
Wheel type
Aluminum
Steel
Inside
Outside
Maximum radial
runout limit
Lateral mm (in)
0.3 (0.012) or less
0.8 (0.031) or less
0.8 (0.031) or less
Radial mm (in)
0.3 (0.012) or less
0.6 (0.024) or less
0.6 (0.024) or less
Maximum residual im-
balance
Dynamic (at rim flange)
Less than 5 g (0.18 oz) (per side)
Static (at rim flange)
Less than 10 g (0.35 oz)
Tire size
Air pressure
Conventional tire
Spare tire
P235/75R15
240 (2.4, 35)
240 (2.4, 35)
P265/70R16
240 (2.4, 35)
240 (2.4, 35)
P265/75R16
240 (2.4, 35)
240 (2.4, 35)
P265/60R18
240 (2.4, 35)
240 (2.4, 35)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст