Nissan Frontier D40. Manual — part 183
CL-18
< REMOVAL AND INSTALLATION >
CLUTCH RELEASE MECHANISM
• Install the release bearing to release bearing sleeve using suitable
tool, as shown.
• Clean old grease and abrasive materials off the grease application areas.
• Apply grease to the specified points as shown.
• Apply approximately 1 mm (0.04 in) thick coat of clutch sleeve grease to withdrawal lever and holder spring
frictional surfaces.
• Apply a coat of clutch sleeve grease to ball pin contact surface of the withdrawal lever and inner slots of the
release bearing. The grease surface should be level with the surrounding area.
• Apply a thin coat of clutch sleeve grease to the release bearing frictional surface. After grease application,
Install release bearing. Wipe off excess grease forced out during bearing installation.
CAUTION:
• Before installing the manual transaxle to the vehicle, check that each sliding surface slides smoothly
by operating withdrawal lever.
• Be careful not to bring any grease into contact with the clutch disc facing, pressure plate surface, or
flywheel surface.
• When assembling, make sure that both ends of the snap
spring touch the end face of the withdrawal lever.
• Be careful with the orientation of the installation.
6M/T : Inspection
INFOID:0000000005276149
INSPECTION AFTER REMOVAL
WCL025
SCIA1362E
SCIA6903E
CLUTCH RELEASE MECHANISM
CL-19
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
• Replace the release bearing if it is seized, damaged, faulty in rota-
tion direction, or has poor aligning function.
• Replace the withdrawal lever if its contact surface is worn abnor-
mally.
• Replace the dust seal if it is deformed or cracked.
SCL733
CL-20
< REMOVAL AND INSTALLATION >
CLUTCH DISC, CLUTCH COVER
CLUTCH DISC, CLUTCH COVER
5M/T
5M/T : Exploded View
INFOID:0000000005276150
5M/T : Removal and Installation
INFOID:0000000005276151
CAUTION:
• Do not clean the clutch disc with solvent.
• When installing, do not get grease from the main drive shaft onto the clutch disc friction surface.
REMOVAL
1.
Remove the manual transmission from the vehicle. Refer to
TM-19, "Removal and Installation from Vehi-
2.
Remove the clutch cover bolts using power tool. Remove the clutch cover and clutch disc.
INSTALLATION
1.
Apply recommended grease to clutch disc and main drive shaft spline.
CAUTION:
Do not allow grease to contaminate the clutch facing.
1.
Flywheel
2.
Clutch disc
3.
Clutch cover
WCIA0522E
CLUTCH DISC, CLUTCH COVER
CL-21
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
2.
Install clutch disc and clutch cover. Pre-tighten the bolts and
install Tool. Then tighten the clutch cover bolts evenly in two
steps to the specified torque in the order shown. Refer to
3.
Install the manual transmission. Refer to
TM-19, "Removal and Installation from Vehicle"
5M/T : Inspection after Removal
INFOID:0000000005276152
INSPECTION AFTER REMOVAL
Clutch Disc
• Check the wear of the clutch disc facing.
• Check the runout and backlash of the clutch disc. If the measure-
ment exceeds the specification, replace the clutch disc.
Clutch Cover
• Check clutch cover thrust ring for wear or damage. If wear or damage is found, replace clutch cover assem-
bly.
NOTE:
• Worn thrust ring will generate a beating noise when tapped at the rivet with a hammer.
Tool number
: ST20630000 (J-26366)
WCIA0504E
Clutch disc facing
wear
: Refer to
SCL229
Runout and backlash
: Refer to
.
SCL221
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст