Nissan Frontier D40. Manual — part 921
PWC-66
< ON-VEHICLE REPAIR >
FRONT POWER WINDOW SWITCH
FRONT POWER WINDOW SWITCH
Removal and Installation
INFOID:0000000005274664
REMOVAL
1.
Remove the front power window switch finisher (2) from the front
door finisher RH. Refer to
INT-14, "Removal and Installation"
.
: Metal clip
:Pawl
2.
Release the four tabs (A), two on each side, then separate the
front power window switch (1) from the finisher (2).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA1098ZZ
REAR POWER WINDOW SWITCH
PWC-67
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR POWER WINDOW SWITCH
Removal and Installation - Rear Door Switch (if equipped)
INFOID:0000000005274665
REMOVAL
1.
Remove the rear power window switch finisher (2) from the rear
door finisher. Refer to
INT-14, "Removal and Installation"
.
: Metal clip
:Pawl
2.
Release the two tabs (A), one on either side, then separate the
rear power window switch (1) from the finisher (2).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA1099ZZ
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
COMPONENT DIAGNOSIS . . . . . . ..
POWER SOCKET . . . . . . . . . . . ..
Wiring Diagram - Power Socket - . . . . . . . .
ON-VEHICLE REPAIR . . . . . . . . ..
POWER SOCKET . . . . . . . . . . . ..
PWO-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005550750
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст