Nissan Frontier D40. Manual — part 93
BRC-70
< REMOVAL AND INSTALLATION >
[TYPE 1]
SENSOR ROTOR
SENSOR ROTOR
Removal and Installation
INFOID:0000000005275111
FRONT
Removal and Installation
The wheel sensor rotors are built into the wheel hubs and are not removable. If damaged, replace wheel hub
and bearing assembly. Refer to
FAX-8, "Removal and Installation"
REAR (C200)
Removal and Installation
It is necessary to disassemble the rear axle to replace the sensor rotor. Perform the axle shaft assembly
removal procedure to replace sensor rotor. Refer to
RAX-7, "Removal and Installation"
.
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
BRC-71
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
Removal and Installation
INFOID:0000000005275112
Type 1
REMOVAL
1.
Disconnect the negative battery terminal.
2.
Drain the brake fluid. Refer to
.
3.
Remove air cleaner case. Refer to
.
4.
Disconnect the actuator harness from the ABS actuator and electric unit (control unit).
CAUTION:
• To remove the brake tubes, use a flare nut wrench to prevent the flare nuts and brake tubes from
being damaged.
• Be careful not to splash brake fluid on painted areas.
5.
Disconnect the brake tubes.
6.
Remove the bolts and remove the ABS actuator and electric unit (control unit).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning steering both clockwise and coun-
terclockwise.
WFIA0388E
1.
To rear left and right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
2.
To front left disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
3.
To front right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
4.
From the master cylinder secondary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
5.
From the master cylinder primary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
6.
ABS actuator and electric unit
(control unit)
7.
Harness connector
8.
Grommet
9.
Collar
BRC-72
< REMOVAL AND INSTALLATION >
[TYPE 1]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• When removing components, cover connections so that no dirt, dust, or other foreign matter gets in.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), refill brake system with new
brake fluid. Then bleed the air from the system. Refer to
BR-21, "Bleeding Brake System"
.
APPLICATION NOTICE
BRC-73
< BASIC INSPECTION >
[TYPE 2]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
BASIC INSPECTION
APPLICATION NOTICE
Application Notice
INFOID:0000000005548386
Service information
Remarks
TYPE 1
ABS
TYPE 2
VDC/TCS/ABS
TYPE 3
HILL DESCENT CONTROL/HILL START ASSIST/VDC/TCS/ABS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст