Nissan Murano Z50 (2006 year). Manual — part 195
AUTOMATIC DRIVE POSITIONER
SE-63
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
Check Rear Lifting Sensor Circuit
NIS001FQ
1.
CHECK REAR END LIFTING SENSOR INPUT/OUTPUT SIGNAL
With CONSULT-II
Check operation with “LIFT RR PULSE” on the DATA MONITOR to make sure pulse changes.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check signal between driver seat control unit connector and
ground, with oscilloscope.
OK or NG
OK
>> Rear lifting sensor circuit is OK.
NG
>> GO TO 2.
2.
CHECK REAR LIFTING SENSOR CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and rear lifting motor connector.
2.
Check continuity between driver seat control unit connector B303 terminals 10, 31 and rear lifting motor
connector B310 terminals 10, 31C.
3.
Check continuity between driver seat control unit connector
B303 terminals 10, 31 and ground.
OK or NG
OK
>> Replace rear lifting motor.
NG
>> Repair or replace harness between driver seat control
unit and rear lifting motor.
Monitor item [OPERATION or UNIT
LIFT RR PULSE
—
The rear lifting position (pulse) judged from
the rear lifting sensor is displayed.
PIIA4558E
Connector
Terminals
(Wire color)
Condition
Signal
(+)
(–)
B303
10 (W/R)
Ground
Rear lift-
ing motor
operation
PIIA4563E
PIIA3278E
10 (W/R) – 10 (W/R)
: Continuity should exist.
31 (R/W) – 31C (R/W)
: Continuity should exist.
10 (W/R) – Ground
: Continuity should not exist.
31 (R/W) – Ground
: Continuity should not exist.
PIIA4564E
SE-64
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
Check Pedal Adjusting Sensor Circuit
NIS001FR
1.
CHECK FUNCTION
With CONSULT-II
Operate the pedal adjusting switch with “PEDAL SEN” on the DATA
MONITOR to make sure the voltage changes.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between automatic drive positioner connector
and ground.
OK or NG
OK
>> Pedal adjusting sensor circuit is OK.
NG
>> GO TO 2.
Monitor item [OPERA-
TION or UNIT]
Contents
PEDAL
SEN
“V”
The pedal adjusting position (voltage) judged from the
pedal adjust sensor signal is displayed.
PIIA4568E
Connector
Terminals
(Wire color)
Condition
Voltage (V)
(Approx)
(+)
(–)
M19
8 (P/B)
Ground
Pedal
front end position
0.5
Pedal
back end position
4.5
PIIA4569E
AUTOMATIC DRIVE POSITIONER
SE-65
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
2.
CHECK PEDAL ADJUSTING SENSOR CIRCUIT HARNESS CONTINUITY
1.
Disconnect automatic drive positioner control unit and pedal adjusting motor connector.
2.
Check continuity between automatic drive positioner connector M19, M20 terminals 8, 33, 41 and pedal
adjusting motor connector E114 terminals 3, 4, 5.
3.
Check continuity between automatic drive positioner control unit
connector E114 terminals 8, 33, 41 and ground.
OK or NG
OK
>> Replace pedal adjusting motor.
NG
>> Repair or replace harness between automatic drive
positioner and pedal adjusting sensor.
Check Mirror Sensor LH Circuit
NIS001FS
1.
CHECK DOOR MIRROR FUNCTION
Check the following items.
Operation malfunction in memory control
NOTE:
If a door mirror face position is set to an implausible angle, the set position may not be reproduced.
OK or NG
OK
>> GO TO 2.
NG
>> Repair the malfunctioning parts, and check the symptom again.
8 (P/B) – 4 (P/B)
: Continuity should exist.
33 (W/L) – 5 (W/L)
: Continuity should exist.
41 (Y) – 3 (Y)
: Continuity should exist.
8 (P/B) – Ground
: Continuity should not exist.
33 (W/L) – Ground
: Continuity should not exist.
41 (Y) – Ground
: Continuity should not exist.
PIIB4131E
SE-66
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
2.
CHECK MIRROR SENSOR CHECK
With CONSULT–II
Check that “ON” is displayed on “MIR/SE LH R–L, MIR/SE LH U–
D" in the DATA MONITOR.
Without CONSULT–II
1.
Turn ignition switch ACC.
2.
Check voltage between door mirror (driver side) connector and ground.
OK or NG
OK
>> Mirror sensor LH is OK.
NG
>> GO TO 3.
3.
CHECK HARNESS CONTINUITY 1
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector and door mirror (driver side) connector.
3.
Check continuity between automatic drive positioner control unit connector M20 terminal 33, 41 and door
mirror (driver side) connector D2 terminal 3, 2.
4.
Check continuity between automatic drive positioner control unit
connector M20 terminal 33, 41 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness between automatic drive
positioner control unit and door mirror (driver side).
Monitor item [OPERATION or
UNIT]
Contents
MIR/
SEN LH R–L
“V”
Voltage output from LH door mirror sensor (LH/
RH) is displayed.
MIR/
SEN LH U–D
“V”
Voltage output from LH door mirror sensor (UP/
DOWN) is displayed.
Con-
nector
Terminals (Wire color)
Condition
Voltage (V)
(Approx,)
(+)
(–)
D2
1 (G)
Ground
When motor is
LEFT or RIGHT
operation
Changes between
3.4 (close to right edge) –
0.6 (close to left edge)
4 (L/Y)
When motor is
UP or DOWN
operation
Changes between
3.4 (close to peak) –
0.6 (close to valley)
PIIA0197E
PIIB3199E
33 (W/L) – 3 (W/L)
:Continuity should exist.
41 (Y) – 2 (Y)
:Continuity should exist.
33 (W/L) – Ground
:Continuity should not exist.
41 (Y) – Ground
:Continuity should not exist.
PIIB3200E
AUTOMATIC DRIVE POSITIONER
SE-67
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
4.
CHECK HARNESS CONTINUITY 2
1.
Check continuity between automatic drive positioner control unit connector M19 terminal 6, 22 and door
mirror (driver side) connector D2 terminal 1, 4.
2.
Check continuity between automatic drive positioner control unit
connector M19 terminal 6, 22 and ground.
OK or NG
OK
>> Replace door mirror (driver side).
NG
>> Repair or replace harness between automatic drive
positioner control unit and door mirror (driver side).
Check Mirror Sensor RH Circuit
NIS001FT
1.
CHECK DOOR MIRROR FUNCTION
Check the following items.
Operation malfunction in memory control
NOTE:
If a door mirror face position is set to an implausible angle, the set position may not be reproduced.
OK or NG
OK
>> GO TO 2.
NG
>> Repair the malfunctioning parts, and check the symptom again.
2.
CHECK MIRROR SENSOR CHECK
With CONSULT–II
Check that “ON” is displayed on “MIR/SE RH R–L, MIR/SE RH U–
D" in the DATA MONITOR.
Without CONSULT–II
1.
Turn ignition switch ACC.
2.
Check voltage between door mirror (passenger side) connector and ground.
OK or NG
OK
>> Mirror sensor RH is OK.
NG
>> GO TO 3.
6 (L/Y) – 4 (L/Y)
:Continuity should exist.
22 (G) – 1 (G)
:Continuity should exist.
6 (L/Y) – Ground
:Continuity should not exist.
22 (G) – Ground
:Continuity should not exist.
PIIB3201E
Monitor item [OPERATION
or UNIT]
Contents
MIR/
SEN RH R–L
“V”
Voltage output from RH door mirror sensor (LH/
RH) is displayed.
MIR/
SEN RH U–D
“V”
Voltage output from RH door mirror sensor (UP/
DOWN) is displayed.
Con-
nector
Terminals (Wire color)
Condition
Voltage(V)
(Approx,)
(+)
(–)
D32
1 (L)
Ground
When motor is
LEFT or RIGHT
operation
Changes between
3.4 (close to left edge) –
0.6 (close to right edge)
4 (R/B)
When motor is
UP or DOWN
operation
Changes between
3.4 (close to peak) –
0.6 (close to valley)
PIIA0197E
PIIB3199E
SE-68
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
3.
CHECK HARNESS CONTINUITY 1
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mirror (passenger side) connector.
3.
Check continuity between automatic drive positioner control unit connector M20 terminal 33, 41 and door
mirror (passenger side) connector D32 terminal 3, 2.
4.
Check continuity between automatic drive positioner control unit
connector M20 terminal 33, 41 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness between automatic drive
positioner control unit and door mirror (passenger side).
4.
CHECK HARNESS CONTINUITY 2
1.
Check continuity between automatic drive positioner control unit
connector M19 terminal 5, 21 and door mirror (passenger side)
connector D32 terminal 1, 4.
2.
Check continuity between automatic drive positioner control unit
connector M19 terminal 5, 21 and ground.
OK or NG
OK
>> Replace door mirror (passenger side).
NG
>> Repair or replace harness between automatic drive positioner control unit and door mirror (pas-
senger side).
33 (W/L) – 3 (W/L)
:Continuity should exist.
41 (Y) – 2 (Y)
:Continuity should exist.
33 (W/L) – Ground
:Continuity should not exist.
41 (Y) – Ground
:Continuity should not exist.
PIIB3200E
5 (R/B) – 4 (R/B)
:Continuity should exist.
21 (L) – 1 (L)
:Continuity should exist.
5 (R/B) – Ground
:Continuity should not exist.
21 (L) – Ground
:Continuity should not exist.
PIIB3202E
AUTOMATIC DRIVE POSITIONER
SE-69
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
Check Sliding Switch Circuit
NIS001FU
1.
CHECK FUNCTION
With CONSULT-II
With “SLIDE SW-FR, SLIDE SW-RR” on the DATA MONITOR, oper-
ate the sliding switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and ground.
OK or NG
OK
>> Sliding switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK SLIDING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat switch connector.
2.
Check continuity between driver seat control unit connector
B303 terminals 11, 26 and power seat switch connector B305
terminals 11, 26.
3.
Check continuity between driver seat control unit connector
B303 terminals 11, 26 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control unit and power seat switch.
Monitor item [OPER-
ATION or UNIT]
Contents
SLIDE SW–
FR
"ON/
OFF"
ON / OFF status judged from the sliding switch (FR)
signal is displayed.
SLIDE SW–
RR
"ON/
OFF"
ON / OFF status judged from the sliding switch (RR)
signal is displayed.
PIIA0313E
Connector
Terminal
(Wire color)
Condition
Voltage (V)
(Approx)
(+)
(–)
B303
11 (W/V)
Ground
Sliding switch
ON(RR operation)
0
Sliding switch OFF
Battery voltage
26 (G/W)
Sliding switch
ON(FR operation)
0
Sliding switch OFF
Battery voltage
PIIA4577E
11 (W/V) – 11 (W/V)
: Continuity should exist.
26 (G/W) – 26 (G/W)
: Continuity should exist.
11 (W/V) – Ground
: Continuity should not exist.
26 (G/W) – Ground
: Continuity should not exist.
PIIA4578E
SE-70
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
3.
CHECK SLIDING SWITCH
Check continuity between power seat switch as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch.
Check Reclining Switch
NIS001FV
1.
CHECK FUNCTION
With CONSULT-II
With “RECLINING SW-FR, RECLINING SW-RR” on the DATA MON-
ITOR, operate the reclining switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Reclining switch circuit is OK.
NG
>> GO TO 2.
Connector
Terminal
Condition
Continuity
B305
11
32A
Sliding switch ON (RR operation)
Yes
Sliding switch OFF
No
26
Sliding switch ON (FR operation)
Yes
Sliding switch OFF
No
PIIA4579E
Monitor item [OPERA-
TION or UNIT]
Contents
RECLN SW
–FR
“ON/
OFF”
ON/OFF status judged from the reclining switch (FR)
signal is displayed.
RECLIN S
W–RR
“ON/
OFF”
ON/OFF status judged from the reclining switch (RR)
signal is displayed.
PIIA0313E
Connector
Terminals
(Wire color)
Condition
Voltage (V)
(Approx)
(+)
(–)
B303
12 (G/Y)
Ground
Reclining switch ON
(RR operation)
0
Reclining switch
OFF
Battery voltage
27 (L/W)
Reclining switch ON
(FR operation)
0
Reclining switch
OFF
Battery voltage
PIIA4580E
AUTOMATIC DRIVE POSITIONER
SE-71
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
2.
CHECK RECLINING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat switch connector.
2.
Check continuity between driver seat control unit connector
B303 terminals 12, 27 and power seat switch connector B305
terminals 12, 27.
3.
Check continuity between driver seat control unit connector
B303 terminals 12, 27 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control unit and power seat switch.
3.
CHECK RECLINING SWITCH
Check continuity between driver seat switch as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch.
12 (G/Y) – 12 (G/Y)
: Continuity should exist.
27 (L/W) – 27 (L/W)
: Continuity should exist.
12 (G/Y) – Ground
: Continuity should not exist.
27 (L/W) – Ground
: Continuity should not exist.
PIIA4581E
Connector
Terminal
Condition
Continuity
B305
12
32A
Reclining switch ON (RR operation)
Yes
Reclining switch OFF
No
27
Reclining switch ON (FR operation)
Yes
Reclining switch OFF
No
PIIA4582E
SE-72
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
Check Front Lifting Switch Circuit
NIS001FW
1.
CHECK FUNCTION
With CONSULT-II
With “LIFT FR SW-UP, LIFT FR SW-DN” on the DATA MONITOR,
operate the front lifting switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Front lifting switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK FROUNT RIFTING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat switch connector.
2.
Check continuity between driver seat control unit connector
B303 terminals 13, 28 and driver seat switch connector B305
terminals 13, 28.
3.
Check continuity between driver seat control unit connector
B303 terminals 13, 28 and ground
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control unit and power seat switch.
Monitor item [OPERA-
TION or UNIT]
Contents
LIFT FR SW–
DN
"ON/
OFF"
ON / OFF status judged from the FR lifter switch
(DOWN) signal is displayed.
LIFT RR SW–
UP
"ON/
OFF"
ON / OFF status judged from the RR lifter switch
(UP) signal is displayed.
PIIA0323E
Connector
Terminals
(Wire color)
Condition
Voltage (V)
(Approx)
(+)
(–)
B303
13 (O/B)
Ground
Front lifting switch ON
(DOWN operation)
0
Front lifting switch OFF
Battery voltage
28 (L/R)
Front lifting switch ON
(UP operation)
0
Front lifting switch OFF
Battery voltage
PIIA4583E
13 (O/B) – 13 (O/B)
: Continuity should exist.
28 (L/R) – 28 (L/R)
: Continuity should exist.
13 (O/B) – Ground
: Continuity should not exist.
28 (L/R) – Ground
: Continuity should not exist.
PIIA4584E
AUTOMATIC DRIVE POSITIONER
SE-73
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
3.
CHECK FRONT LIFTING SWITCH
Check continuity between driver seat switch as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch (driver side).
Check Rear Lifting Switch Circuit
NIS001FX
1.
CHECK FUNCTION
With CONSULT-II
With “LIFT RR SW-UP, LIFT RR SW-DN” on the DATA MONITOR,
operate the rear lifting switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Rear lifting switch circuit is OK.
NG
>> GO TO 2.
Connector
Terminals Condition
Continuity
B305
13
32A
Front lifting switch ON (DOWN operation)
Yes
Front lifting switch OFF
No
28
Front lifting switch ON (UP operation)
Yes
Front lifting switch OFF
No
PIIA4585E
Monitor item [OPERATION or
UNIT]
Contents
LIFT RR SW–UP
“ON/OFF”
Operation (ON)/open (OFF) status judged
from the RR lifter switch (UP) signal is dis-
played.
LIFT RR SW–DN
“ON/OFF”
Operation (ON)/open (OFF) status judged
from the RR lifter switch (DOWN) signal is
displayed.
PIIA0323E
Connector
Terminals
(Wire color)
Condition
Voltage (V)
(Approx)
(+)
(–)
B303
14 (Y/R)
Ground
Rear lifting switch ON
(DOWN operation)
0
Rear lifting switch OFF
Battery voltage
29 (W/G)
Rear lifting switch ON
(UP operation)
0
Rear lifting switch OFF
Battery voltage
PIIA4586E
SE-74
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
2.
CHECK POWER SEAT SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat switch connector.
2.
Check continuity between driver seat control unit connector
B303 terminals 14, 29 and power seat switch connector B305
terminals 14, 29.
3.
Check continuity between driver seat control unit connector
B303 terminals 14, 29 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control unit and power seat switch.
3.
CHECK REAR LIFTING SWITCH
Check continuity between driver seat switch as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch.
Check Power Seat Switch Ground Circuit
NIS001FY
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
Check continuity between power seat switch connector B305 termi-
nal 32A and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Repair or replace harness between power seat switch and ground.
14 (Y/R) – 14 (Y/R)
: Continuity should exist.
29 (W/G) – 29 (W/G)
: Continuity should exist.
14 (Y/R) – Ground
: Continuity should not exist.
29 (W/G) – Ground
: Continuity should not exist.
PIIA4587E
Connector
Terminals
Condition
Continuity
B305
14
32A
Rear lifting switch ON (DOWN operation)
Yes
Rear lifting switch OFF
No
29
Rear lifting switch ON (UP operation)
Yes
Rear lifting switch OFF
No
PIIA4588E
32A (B/W) – Ground
: Continuity should exist.
PIIA4589E
AUTOMATIC DRIVE POSITIONER
SE-75
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
Check Pedal Adjusting Switch Circuit
NIS001FZ
1.
CHECK FUNCTION
With CONSULT-II
With “PEDAL SW-FR, PEDAL SW-RR” on the DATA MONITOR,
operate the pedal adjusting switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Pedal adjusting switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK PEDAL ADJUSTING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and pedal adjusting switch connector.
2.
Check continuity between driver seat control unit connector
B303 terminals 15, 30 and pedal adjusting switch connector
B306 terminals 15, 30.
3.
Check continuity between driver seat control unit connector
B303 terminals 15, 30 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control unit and pedal adjusting switch.
Monitor item [OPERATION or
UNIT]
Contents
PEDAL SW–FR
“ON/OFF”
Operation (ON)/open (OFF) status
judged from the pedal adjusting switch
(FR) signal is displayed.
PEDAL SW–RR
“ON/OFF”
Operation (ON)/open (OFF) status
judged from the pedal adjusting switch
(RR) signal is displayed.
PIIA4590E
Connector
Terminals
(Wire color)
Condition
Voltage (V)
(Approx)
(+)
(–)
B303
15 (G/R)
Ground
Pedal adjusting switch
ON (RR operation)
0
Pedal adjusting switch
OFF
Battery voltage
30 (W/L)
Pedal adjusting switch
ON (FR operation)
0
Pedal adjusting switch
OFF
Battery voltage
PIIA4591E
15 (G/R) – 15 (G/R)
: Continuity should exist.
30 (W/L) – 30 (W/L)
: Continuity should exist.
15 (G/R) – Ground
: Continuity should not exist.
30 (W/L) – Ground
: Continuity should not exist.
PIIA4592E
SE-76
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
3.
CHECK PEDAL ADJUSTING SWITCH
Check continuity between pedal adjust switch as follows.
OK or NG
OK
>> GO TO 4.
NG
>> Replace pedal adjusting switch.
4.
CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector B306
terminal 48C and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace or replace harness between pedal adjusting switch and ground.
Connector
Terminals
Condition
Continu-
ity
B306
15
48C
Pedal adjusting switch ON (RR operation)
Yes
Pedal adjusting switch OFF
No
30
Pedal adjusting switch ON (FR operation)
Yes
Pedal adjusting switch OFF
No
PIIA4593E
48C (B) – Ground
: Continuity should exist.
PIIA4594E
AUTOMATIC DRIVE POSITIONER
SE-77
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision: 2006 August
2006 Murano
Check Door Mirror Remote Control Switch (Changeover Switch) Circuit
NIS001G0
1.
CHECK FUNCTION
With CONSULT–II
Check the operation on “MIR CHNG SW – R” or “MIR CHNG SW–
L" in the DATA MONITOR.
Without CONSULT–II
1.
Turn ignition switch ACC.
2.
Check voltage between automatic drive positioner control unit
connector and ground.
OK or NG
OK
>> Door mirror remote control switch (changeover switch) is OK.
NG
>> GO TO 2.
2.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH CIRCUIT HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mirror remote control switch connector.
3.
Check continuity between automatic drive positioner control unit
connector M19 terminal 2, 18 and door mirror remote control
switch connector M66 terminal 3, 2.
4.
Check continuity between automatic drive positioner control unit
connector M19 terminal 2, 18 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between automatic drive positioner control unit and door remote control
switch.
Monitor item [OPERATION
or UNIT]
Contents
MIR CHNG S
W–R
“ON/OFF”
ON/OFF status judged from the door mirror remote
control switch (switching to RIGHT) signal is dis-
played.
MIR CHNG S
W–L
“ON/OFF”
ON/OFF status judged from the door mirror remote
control switch (switching to LEFT) signal is dis-
played.
PIIA0191E
Connector
Terminals (Wire color)
Condition
Voltage (V)
(Approx)
(+)
(-)
M19
2 (L/W)
Ground
Changeover switch
RIGHT position
0
Changeover switch
neutral position
5
18 (BR/Y)
Changeover switch
LEFT position
0
Changeover switch
neutral position
5
PIIA4767E
2 (L/W) – 3 (L/W)
:Continuity should exist.
18 (BR/Y) – 2 (BR/Y)
:Continuity should exist.
2 (L/W) – Ground
:Continuity should not exist.
18 (BR/Y) – Ground
:Continuity should not exist.
PIIB4132E
SE-78
AUTOMATIC DRIVE POSITIONER
Revision: 2006 August
2006 Murano
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH (CHANGEOVER SWITCH)
Check continuity between door mirror remote control switch as follows.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace door mirror remote control switch.
Check Door Mirror Remote Control Switch (Mirror Switch) Circuit
NIS001G1
1.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH(MIRROR SWITCH) SIGNAL
With CONSULT–II
Check the operation on “MIR CON SW–UP/DN” and
“MIR CON SW–RH/LH” in the DATA MONITOR.
Without CONSULT–II
1.
Turn ignition switch ACC.
2.
Check voltage between automatic drive positioner control unit
connector and ground.
OK or NG
OK
>> Door mirror remote control switch (mirror switch) circuit is OK.
NG
>> GO TO 2.
Connector
Terminals
Condition
Continuity
M66
3
13
Changeover switch RIGHT position
Yes
Changeover switch neutral position
No
2
Changeover switch LEFT position
Yes
Changeover switch neutral position
No
PIIB4133E
Monitor item [OPERATION
or UNIT]
Contents
MIR CON SW
–UP
“ON/OFF”
ON/OFF status judged from the door mirror remote
control switch (UP) signal is displayed.
MIR CON SW
–DN
“ON/OFF”
ON/OFF status judged from the door mirror remote
control switch (DOWN) signal is displayed.
MIR CON SW
–RH
“ON/OFF”
ON/OFF status judged from the door mirror remote
control switch (RIGHT) signal is displayed.
MIR CON SW
–LH
“ON/OFF”
ON/OFF status judged from the door mirror remote
control switch (LEFT) signal s displayed.
PIIA0199E
Con-
nector
Terminals (Wire color)
Condition
Voltage (V)
(Approx)
(+)
(-)
M19
3 (Y/B)
Ground
Mirror switch UP operation
0
Mirror switch neutral position
5
4 (V/W)
Mirror switch LEFT operation
0
Mirror switch neutral position
5
19 (L/O)
Mirror switch DOWN operation
0
Mirror switch neutral position
5
20 (V)
Mirror switch RIGHT operation
0
Mirror switch neutral position
5
PIIA4771E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст