Nissan Murano Z50 (2006 year). Manual — part 68
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-193
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
.
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-229, "Removal and Installation"
.
NG
>> Repair or replace damaged parts.
CVT-194
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 August
2006 Murano
Vehicle Does Not Creep Backward in “R” Position
NCS00190
SYMPTOM:
Vehicle does not creep backward when selecting “R” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-212, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
SCIA2001E
SAT638A
SAT494G
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-195
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
5.
CHECK SYMPTOM
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
.
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-229, "Removal and Installation"
.
NG
>> Repair or replace damaged parts.
CVT-196
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 August
2006 Murano
Vehicle Does Not Creep Forward in “D”, “S” or “L” Position
NCS00191
SYMPTOM:
Vehicle does not creep forward when selecting “D”, “S”*, or “L”* position.
*: Without manual mode
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-212, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
SCIA2001E
SAT638A
SAT494G
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-197
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
5.
CHECK SYMPTOM
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
.
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-229, "Removal and Installation"
.
NG
>> Repair or replace damaged parts.
CVT-198
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 August
2006 Murano
CVT Does Not Shift
NCS00192
SYMPTOM:
CVT does not shift at the specified speed on “Cruise Test”.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-212, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
SCIA2001E
SAT638A
SAT494G
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-199
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
5.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
.
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-229, "Removal and Installation"
.
NG
>> Repair or replace damaged parts.
CVT-200
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 August
2006 Murano
Cannot Be Changed to Manual Mode
NCS00193
SYMPTOM:
Does not change to manual mode when manual shift gate is used.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK MANUAL MODE SWITCH
Check the manual mode switch circuit. Refer to
CVT-132, "DTC P0826 MANUAL MODE SWITCH CIRCUIT"
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
SYMPTOM CHECK
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 4.
4.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-201
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
CVT Does Not Shift in Manual Mode
NCS00194
SYMPTOM:
Speed does not change even if the selector lever is put in the manual shift gate position and the selec-
tor lever is operated to + side or to - side.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK MANUAL MODE SWITCH
Check the manual mode switch circuit. Refer to
CVT-132, "DTC P0826 MANUAL MODE SWITCH CIRCUIT"
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-212, "Checking of CVT Position"
OK or NG
OK
>> GO TO 4.
NG
>> Adjust control cable. Refer to
.
4.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
OK or NG
OK
>> GO TO 5.
NG
>> Refill CVT fluid.
SCIA2001E
SAT638A
CVT-202
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 August
2006 Murano
5.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 6.
NG
>> Check the malfunctioning item. Refer to
6.
CHECK SYMPTOM
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 7.
7.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-229, "Removal and Installation"
NG
>> Repair or replace damaged parts.
SAT494G
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-203
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
Cannot Be Changed to Second Position (WITHOUT MANUAL MODE)
NCS00195
SYMPTOM:
Does not change to second position when selecting “S” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK SECOND POSITION SWITCH
Check the second position switch circuit. Refer to
CVT-178, "SECOND POSITION SWITCH"
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 4.
4.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
.
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
CVT-204
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 August
2006 Murano
Cannot Be Changed to “L” Position (WITHOUT MANUAL MODE)
NCS00196
SYMPTOM:
Does not change to “L” position when selecting “L” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-212, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
SCIA2001E
SAT638A
SAT494G
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-205
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
5.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
.
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-229, "Removal and Installation"
.
NG
>> Repair or replace damaged parts.
CVT-206
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2006 August
2006 Murano
Vehicle Does Not Decelerate by Engine Brake
NCS00197
SYMPTOM:
No engine brake is applied when the gear is shifted from the “M2” to “M1” position.
No engine brake is applied when the gear is shifted from the “S”* to “L” position.
*: Without manual mode
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis check. Refer to
CVT-65, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system. Refer to
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-212, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK (With manual mode) >>GO TO 5.
OK (Without manual mode) >>GO TO 6.
NG
>> Check the malfunctioning item. Refer to
SCIA2001E
SAT638A
SAT494G
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-207
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2006 August
2006 Murano
5.
CHECK MANUAL MODE SWITCH
Check the manual mode switch circuit. Refer to
CVT-132, "DTC P0826 MANUAL MODE SWITCH CIRCUIT"
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace damaged parts.
6.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 7.
7.
CHECK TCM
1.
Check TCM input/output signals. Refer to
CVT-57, "TCM Input/Output Signal Reference Values"
.
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-229, "Removal and Installation"
.
NG
>> Repair or replace damaged parts.
CVT-208
SHIFT CONTROL SYSTEM
Revision: 2006 August
2006 Murano
SHIFT CONTROL SYSTEM
PFP:34901
Removal and Installation
NCS00198
CONTROL DEVICE COMPONENTS (WITH MANUAL MODE)
1.
Selector lever knob
2.
Knob cover
3.
A/T console finisher
4.
Control device assembly
5.
Control cable
6.
Lock plate
7.
Lock pin
SCIA6463E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст