Nissan Murano Z50 (2006 year). Manual — part 169
INTERIOR ROOM LAMP
LT-203
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
Terminals and Reference Values for BCM
NKS001RE
*1: With Intelligent Key
*2: Without Intelligent Key
How to Proceed with Trouble Diagnosis
NKS001RF
1.
Confirm the symptom or customer complaint.
2.
Understand operation description and function description. Refer to
.
3.
Carry out the Preliminary Check. Refer to
4.
Check symptom and repair or replace the cause of malfunction.
5.
Does the interior room lamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
Terminal
No.
Wire color
Signal name
Measuring condition
Reference value
Ignition
switch
Operation or condition
1
R/Y
Ignition key hole illumination
signal
OFF
Door is locked. (SW OFF)
Battery voltage
Door is unlocked. (SW ON)
Approx. 0 V
12
R/G
*1
R
*2
Front door switch AS signal
OFF
Front door
switch AS
ON (open)
Approx. 0 V
OFF (closed)
Battery voltage
13
R/W
*1
R/Y
*2
Rear door switch RH signal
OFF
Rear door
switch RH
ON (open)
Approx. 0 V
OFF (closed)
Battery voltage
22
BR/W
Power window switch serial
link
—
—
37
B/R
Key-in detection switch
signal
OFF
Vehicle key is removed.
Approx. 0 V
Vehicle key is inserted.
Battery voltage
38
R
Ignition power supply
ON
—
Battery voltage
39
L
CAN
−
H
—
—
—
40
Y
CAN
−
L
—
—
—
41
P
Battery saver output signal
OFF
30 minutes after ignition switch
is turned to OFF.
Approx. 0 V
ON
—
Battery voltage
42
GR
Battery power supply
OFF
—
Battery voltage
47
R/W
Step lamp signal
OFF
Any door is open. (ON)
Approx. 0 V
All doors are closed. (OFF)
Battery voltage
48
R
Personal lamp LH and RH,
and room lamp illumination
output signal
OFF
Interior
door switch:
DOOR
position
Any
door
switch
ON
(open)
Approx. 0 V
OFF
(closed)
Battery voltage
52
B
Ground
ON
—
Approx. 0 V
55
W/B
Battery power supply
OFF
—
Battery voltage
58
V/W
Back door switch signal
OFF
Back door
switch
ON (open)
Approx. 0 V
OFF (closed)
Battery voltage
62
SB
Front door switch DR signal
OFF
Front door
switch DR
ON (open)
Approx. 0 V
OFF (closed)
Battery voltage
63
R/W
Rear door switch LH signal
OFF
Rear door
switch LH
ON (open)
Approx. 0 V
OFF (closed)
Battery voltage
PIIA2344J
LT-204
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
6.
INSPECTION END
Preliminary Check
NKS001RG
CHECK FOR POWER SUPPLY AND GROUND CIRCUIT
1.
CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
Refer to
LT-189, "Wiring Diagram — ROOM/L —"
OK or NG
OK
>> GO TO 2.
NG
>> If fuse or fusible link is blown, be sure to eliminate cause of malfunction before installing new fuse
PG-3, "POWER SUPPLY ROUTING CIRCUIT"
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK
>> INSPECTION END
NG
>> Repair harness or connector.
Unit
Power source
Fuse and fusible link No.
BCM
Battery
F
18
21
22
Ignition switch ON or START position
1
(+)
(
−
)
Ignition switch position
BCM con-
nector
Terminal
OFF
ON
M34
38
Approx. 0 V
Battery voltage
M35
42
Ground
Battery voltage
Battery voltage
55
Battery voltage
Battery voltage
PKIB5199E
BCM connector
Terminal
Ground
Continuity
M35
52
Yes
PKIB5198E
INTERIOR ROOM LAMP
LT-205
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
CONSULT-II Functions (BCM)
NKS002TW
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to
GI-38, "CONSULT-II Start Procedure"
.
WORK SUPPORT (INT LAMP)
Operation Procedure
1.
Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “SET I/L D
−
UNLCK INTCON” on “SELECT WORK ITEM” screen.
4.
Touch “START”.
5.
Touch “CHANGE SETT”.
6.
The setting will be changed and “CUSTOMIZING COMPLETED ” will be displayed.
7.
Touch “END”.
Display Item List
Reference between “MODE” and “TIME” for “TURN ON/OFF”
DATA MONITOR (INT LAMP)
Operation Procedure
1.
Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4.
When “SELECTION FROM MENU” is selected, touch items to be monitored. When “ALL SIGNALS” is
selected, all items will be monitored.
5.
Touch “START”.
6.
Touch “RECORD” while monitoring, then the status of monitored item can be recorded. To stop recording,
touch “STOP”.
BCM diagnosis part
Diagnosis mode
Description
INT LAMP
WORK SUPPORT
Changes the setting for each function.
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending driving signal to them.
BATTERY SAVER
WORK SUPPORT
Changes the setting for each function.
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending driving signal to them.
Item
Description
CONSULT-II
SET I/L D
−
UNLCK INTCON
The 30 seconds glowing function interior room lamps and ignition keyhole illu-
mination can be selected when driver door is released (unlocked).
ON/OFF
ROOM LAMP ON TIME SET
The time in order to escalate illumination can be adjusted when interior room
lamps and ignition keyhole illumination is turned on.
MODE 1 – 7
ROOM LAMP OFF TIME SET
The time in order to diminish illumination can be adjusted when interior room
lamps and ignition keyhole illumination is turned off.
MODE 1 – 7
MODE
1
2
3
4
5
6
7
Time (sec.)
0.5
1
2
3
4
5
0
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects items and monitor them.
LT-206
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
Display Item List
NOTE:
Vehicle with intelligent key system display this item.
ACTIVE TEST (INT LAMP)
Operation Procedure
1.
Touch “INT LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch item to be tested and check operation of the selected item.
4.
During the operation check, touching “OFF” deactivates the operation.
Display Item List
NOTE:
This item is displayed, but cannot be tested.
WORK SUPPORT (BATTERY SAVER)
Operation Procedure
1.
Touch “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “ROOM LAMP BAT SAV SET” on “SELECT WORK ITEM” screen.
4.
Touch “START”.
5.
Touch “CHANGE SETT”.
6.
The setting will be changed and “CUSTOMIZING COMPLETED ” will be displayed.
7.
Touch “END”.
Monitor item
Contents
IGN ON SW
“ON/OFF”
Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch signal.
KEY ON SW
“ON/OFF”
Displays “Key inserted (ON)/key removed (OFF)” status judged from the key switch signal.
DOOR SW - DR
“ON/OFF”
Displays status of the driver door as judged from the driver door switch signal. (Door is open:
ON/Door is closed: OFF)
DOOR SW - AS
“ON/OFF”
Displays status of the passenger door as judged from passenger door switch signal. (Door
open (ON)/Door closed (OFF))
DOOR SW - RR
“ON/OFF”
Displays status of rear door as judged from the rear door switch (RH) signal. (Door is open: ON/
Door is closed: OFF)
DOOR SW - RL
“ON/OFF”
Displays status of rear door as judged from the rear door switch (LH) signal. (Door is open: ON/
Door is closed: OFF)
BACK DOOR SW
“ON/OFF”
Displays status of the back door as judged from back door switch signal. (Door open (ON)/Door
closed (OFF))
KEY CYL LK - SW
“ON/OFF”
Displays “Door locked (ON) status, determined from key cylinder lock switch in driver door.
KEY CYL UN - SW
“ON/OFF”
Displays “Door unlocked (OFF) status, determined from key cylinder lock switch in driver door.
CDL LOCK SW
“ON/OFF”
Displays “Door locked (ON)/Door unlocked (OFF) status, determined from locking detection
switch in driver door.
CDL UNLOCK SW
“ON/OFF”
Displays “Door unlocked (OFF)” status, determined from locking detection switch in passenger
door.
I
−
KEY LOCK
NOTE
“ON/OFF”
Displays “Locked (ON)/Other (OFF)” status, determined from lock signal.
I
−
KEY UNLOCK
NOTE
“ON/OFF”
Displays “Unlocked (ON)/Other (OFF)” status, determined from unlock signal.
Test item
Description
INT LAMP
Interior room lamp can be operated by any ON
−
OFF operations.
IGN ILLUM
Ignition key hole illumination can be operated by ON
−
OFF operation.
STEP LAMP TEST
All step lamp can be operated by ON
−
OFF operation.
LUGGAGE LAMP TEST
NOTE
—
INTERIOR ROOM LAMP
LT-207
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
Display Item List
DATA MONITOR (BATTERY SAVER)
Operation Procedure
1.
Touch “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.
4.
When “SELECTION FROM MENU” is selected, touch items to be monitored. When “ALL SIGNALS” is
selected, all items will be monitored.
5.
Touch “START”.
6.
Touch “RECORD” while monitoring, then the status of monitored item can be recorded. To stop recording,
touch “STOP”.
Display Item List
NOTE:
Vehicle with intelligent key system display this item.
ACTIVE TEST (BATTERY SAVER)
Operation Procedure
1.
Touch “BATTERY SAVER” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch item to be tested and check operation of the selected item.
4.
During the operation check, touching “OFF” deactivates the operation.
Item
Description
CONSULT-II
ROOM LAMP TIME SET
Interior room lamp battery saver timer setting can be changed.
MODE 1: 30min
MODE 2: 60min
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects items and monitor them.
Monitor item
Contents
IGN ON SW
“ON/OFF”
Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch signal.
KEY ON SW
“ON/OFF”
Displays “Key inserted (ON)/key removed (OFF)” status judged from the key switch signal.
DOOR SW - DR
“ON/OFF”
Displays status of the driver door as judged from the driver door switch signal. (Door is open:
ON/Door is closed: OFF)
DOOR SW - AS
“ON/OFF”
Displays status of the passenger door as judged from passenger door switch signal. (Door
open (ON)/Door closed (OFF))
DOOR SW - RR
“ON/OFF”
Displays status of rear door as judged from the rear door switch (RH) signal. (Door is open: ON/
Door is closed: OFF)
DOOR SW - RL
“ON/OFF”
Displays status of rear door as judged from the rear door switch (LH) signal. (Door is open: ON/
Door is closed: OFF)
BACK DOOR SW
“ON/OFF”
Displays status of the back door as judged from back door switch signal. (Door open (ON)/Door
closed (OFF))
KEY CYL LK - SW
“ON/OFF”
Displays “Door locked (ON) status, determined from key cylinder lock switch in driver door.
KEY CYL UN - SW
“ON/OFF”
Displays “Door unlocked (OFF) status, determined from key cylinder lock switch in driver door.
CDL LOCK SW
“ON/OFF”
Displays “Door locked (ON)/Door unlocked (OFF) status, determined from locking detection
switch in driver door.
CDL UNLOCK SW
“ON/OFF”
Displays “Door unlocked (OFF)” status, determined from locking detection switch in passenger
door.
I
−
KEY LOCK
NOTE
“ON/OFF”
Displays “Locked (ON)/Other (OFF)” status, determined from lock signal.
I
−
KEY UNLOCK
NOTE
“ON/OFF”
Displays “Unlocked (ON)/Other (OFF)” status, determined from unlock signal.
LT-208
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
Display Item List
Room Lamp Does Not Illuminate
NKS001RI
1.
CHECK EACH SWITCH
Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed in display item list turn ON-OFF linked
with switch operation. Refer to
switches and their functions.
OK or NG
OK
>> GO TO 2.
NG
>> Inspect malfunctioning switch system.
2.
CHECK WITH ACTIVE TEST
1.
Select “BCM” on CONSULT-II. Select “INT LAMP” active test.
2.
When room lamp switch is in “DOOR” position, use active test to
make sure room lamp operates.
OK or NG
OK
>> Replace BCM. Refer to
BCS-14, "Removal and Installa-
NG
>> GO TO 3.
3.
CHECK POWER SUPPLY TO ROOM LAMP
1.
Turn ignition switch OFF.
2.
Disconnect room lamp connector.
3.
Turn ignition switch ON.
4.
Check voltage between room lamp harness connector R9 termi-
nal 2 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 6.
Test item
Description
BATTERY SAVER
Interior room lamp can be operated by ON
−
OFF operations.
PKIB3532E
PKIA6366E
2 - Ground
: Battery voltage.
PKIB2173E
INTERIOR ROOM LAMP
LT-209
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
4.
CHECK ROOM LAMP
Check continuity between room lamp terminals.
OK or NG
OK
>> GO TO 5.
NG
>> Check bulb or replace room lamp.
5.
CHECK POWER SUPPLY CIRCUIT FOR ROOM LAMP
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector M35 terminal
48 and room lamp harness connector R9 terminal 1.
OK or NG
OK
>> Replace BCM if room lamp does not work after setting
the connector again. Refer to
NG
>> Repair harness or connector.
6.
CHECK GROUND CIRCUIT FOR ROOM LAMP
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector M35 terminal
41 and room lamp harness connector R9 terminal 2.
OK or NG
OK
>> Replace BCM if room lamp does not work after setting
the connector again. Refer to
NG
>> Repair harness or connector.
Personal Lamp Does Not Illuminate
NKS001RJ
1.
CHECK EACH SWITCH
Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed in display item list turn ON-OFF linked
with switch operation. Refer to
for
switches and their functions.
OK or NG
OK
>> GO TO 2.
NG
>> Inspect malfunctioning switch system.
Terminal
Condition
Continuity
Room lamp
1
2
Room lamp switch is DOOR
Yes
Room lamp switch is OFF
No
PKIB2180E
48 - 1
: Continuity should exist.
PKIB2162E
41 - 2
: Continuity should exist.
PKIB2163E
PKIB3532E
LT-210
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
2.
CHECK WITH ACTIVE TEST
1.
Select “BCM” on CONSULT-II. Select “INT LAMP” active test.
2.
When personal lamp switch is in “DOOR” position, use active
test to make sure personal lamp operates.
OK or NG
OK
>> Replace BCM. Refer to
BCS-14, "Removal and Installa-
NG
>> GO TO 3.
3.
CHECK PERSONAL LAMP INPUT
1.
Turn ignition switch OFF.
2.
Disconnect personal lamp connectors.
3.
Turn ignition switch ON.
4.
Check voltage between personal lamp RH harness connector
R10 terminal 1 and ground.
5.
Check voltage between personal lamp LH harness connector
R8 terminal 1 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 6.
4.
CHECK PERSONAL LAMP
1.
Disconnect personal lamp connector.
2.
Check continuity between personal lamp terminals.
OK or NG
OK
>> GO TO 5.
NG
>> Check bulb or replace personal lamp.
PKIA6366E
1 - Ground
: Battery voltage.
1 - Ground
: Battery voltage.
PKIB7226E
Terminal
Condition
Continuity
Personal lamp
1
3
Personal lamp switch is DOOR
Yes
Personal lamp switch is OFF
No
PKIA6372E
INTERIOR ROOM LAMP
LT-211
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
5.
CHECK PERSONAL LAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector M35 terminal
48 and personal lamp RH harness connector R10 terminal 3.
4.
Check continuity between BCM harness connector M35 terminal
48 and personal lamp LH harness connector R8 terminal 3.
OK or NG
OK
>> Replace BCM if personal amp does not work after setting the connector again. Refer to
"Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
6.
CHECK PERSONAL LAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector M35 terminal
41 and personal lamp RH harness connector R10 terminal 1.
4.
Check continuity between BCM harness connector M35 terminal
41 and personal lamp LH harness connector R8 terminal 1.
OK or NG
OK
>> Replace BCM if personal lamp does not work after setting the connector again. Refer to
"Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
Ignition Key Hole Illumination Does Not Illuminate
NKS001RK
1.
CHECK BULB
Check bulb of lamp which does not operate.
OK or NG
OK
>> GO TO 2.
NG
>> Replace bulb.
2.
CHECK EACH SWITCH
Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed in display item list turn ON-OFF linked
with switch operation. Refer to
for
switches and their functions.
OK or NG
OK
>> GO TO 3.
NG
>> Inspect malfunctioning switch system.
48 - 3
: Continuity should exist.
48 - 3
: Continuity should exist.
PKIB2164E
41 - 1
: Continuity should exist.
41 - 1
: Continuity should exist.
PKIB2165E
PKIB3532E
LT-212
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
3.
CHECK WITH ACTIVE TEST
1.
Select “BCM” on CONSULT-II. Select “INT LAMP” active test.
2.
Select “IGN ILLUM” active test to make sure lamp operates.
OK or NG
OK
>> Replace BCM. Refer to
BCS-14, "Removal and Installa-
NG
>> GO TO 4.
4.
CHECK POWER SUPPLY TO IGNITION KEY HOLE ILLUMINATION
1.
Turn ignition switch OFF.
2.
Disconnect ignition key hole illumination connector.
3.
Turn ignition switch ON.
4.
Check voltage between ignition key hole illumination harness
connector M40 terminal 1 and ground.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
CHECK POWER SUPPLY CIRCUIT FOR IGNITION KEY HOLE ILLUMINATION
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and key hole illumination connector.
3.
Check continuity between BCM harness connector M35 terminal
41 and key hole illumination harness connector M40 terminal 1.
OK or NG
OK
>> Replace BCM if ignition key hole illumination does not
work after setting the connector again. Refer to
"Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
6.
CHECK GROUND CIRCUIT FOR IGNITION KEY HOLE ILLUMINATION
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and key hole illumination connector.
3.
Check continuity between BCM harness connector M34 terminal
1 and key hole illumination harness connector M40 terminal 2.
OK or NG
OK
>> Replace BCM if ignition key hole illumination does not
work after setting the connector again. Refer to
"Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
PKIA6375E
1 - Ground
: Battery voltage.
PKIB7227E
41 - 1
: Continuity should exist.
PKIB3520E
1 - 2
: Continuity should exist.
PKIA6377E
INTERIOR ROOM LAMP
LT-213
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
Step Lamp Does Not Illuminate
NKS001RL
1.
CHECK EACH DOOR SWITCH
Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed below turn ON-OFF linked with switch
operation.
OK or NG
OK
>> GO TO 2.
NG
>> Inspect malfunctioning switch system.
2.
CHECK BULB
Check bulb of lamp which does not illuminate.
OK or NG
OK
>> GO TO 3.
NG
>> Replace bulb.
3.
CHECK STEP LAMP INPUT
1.
Turn ignition switch OFF.
2.
Disconnect step lamp (driver side and passenger side) connec-
tors.
3.
Turn ignition switch ON.
4.
Check voltage between step lamp (driver side) harness connec-
tor D9 terminal 1 and ground.
5.
Check voltage between step lamp (passenger side) harness
connector D37 terminal 1 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 5.
4.
CHECK GROUND CIRCUIT FOR STEP LAMP
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector M35 terminal
47 and step lamp (driver side) harness connector D9 terminal 2.
4.
Check continuity between BCM harness connector M35 terminal
47 and step lamp (passenger side) harness connector D37 ter-
minal 2.
OK or NG
OK
>> Replace BCM if step lamp does not work after setting the connector again. Refer to
"Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
Switch name
CONSULT screen
Driver side door switch
DOOR SW - DR
Passenger side door switch
DOOR SW - AS
PKIB3532E
1 - Ground
: Battery voltage.
1 - Ground
: Battery voltage.
PKIB2181E
47 - 2
: Continuity should exist.
47 - 2
: Continuity should exist.
PKIB2167E
LT-214
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
5.
CHECK STEP LAMP CIRCUIT
1.
Disconnect BCM connector and step lamp connector.
2.
Check continuity between BCM harness connector M35 terminal
41 and step lamp (driver side) harness connector D9 terminal 1.
3.
Check continuity between BCM harness connector M35 terminal
41 and step lamp (passenger side) harness connector D37 ter-
minal 1.
OK or NG
OK
>> Replace BCM if step lamp does not work after setting the connector again. Refer to
"Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
All Interior Room Lamp Does Not Operate
NKS001RM
1.
CHECK POWER SUPPLY CIRCUIT
1.
All interior room lamps switch are OFF.
2.
Turn ignition switch ON.
3.
Check voltage between BCM harness connector M35 terminal
41 and ground.
OK or NG
OK
>> Repair harness or connector. In a case of making a
short circuit, be sure to disconnect battery negative
cable after repairing harness, and then reconnect
NG
>> Replace BCM. Refer to
BCS-14, "Removal and Installa-
Bulb Replacement
NKS001RN
MAP LAMP
1.
Disconnect the battery negative cable.
2.
Remove the lens using clip driver or suitable tool.
3.
Remove the bulb.
4.
Installation is the reverse order of removal.
PERSONAL LAMP
1.
Remove the personal lamp. Refer to
.
41 - 1
: Continuity should exist.
41 - 1
: Continuity should exist.
PKIB2168E
41 - Ground
: Battery voltage
PKIB3524E
Map lamp
: 12V - 8 W
PKIA2534E
INTERIOR ROOM LAMP
LT-215
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
2.
Remove the housing mounting screws, and separate it.
3.
Remove bulb from the base.
4.
Installation is the reverse order of removal.
ROOM LAMP
1.
Disconnect the battery negative cable.
2.
Remove the lens using clip driver or suitable tool.
3.
Remove the bulb.
4.
Installation is the reverse order of removal.
STEP LAMP
1.
Disconnect the battery cable from the negative terminal or
remove power fuse.
2.
Insert a screwdriver in the chink between lens and door trim,
and remove the lens.
3.
Remove the bulb.
4.
Installation is the reverse order of removal.
Personal lamp
: 12V - 8W
PKIA2536E
Room lamp
: 12V - 8W
PKIA2535E
Step lamp
: 12V - 2.7W
PKIB2175E
LT-216
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
LUGGAGE ROOM LAMP
1.
Remove luggage room lamp. Refer to
2.
Remove the bulb.
3.
Installation is the reverse order of removal.
VANITY MIRROR LAMP
1.
Insert a thin screwdriver in the notch and remove lens.
2.
Remove bulb.
3.
Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION
Without intelligent key system
1.
Remove the ignition key finisher. Refer to
2.
Turn the bulb socket counterclockwise and unlock it.
With intelligent key system
1.
Remove the ignition key finisher. Refer to
2.
Remove the steering look escutcheon.
3.
Turn the bulb socket counterclockwise and unlock it.
Luggage room lamp
: 12V - 8W
PKIA2537E
Vanity mirror lamp
: 12V - 2W
PKIB2178E
Ignition key hole illumination
: 12V - 0.8W
PKIB2182E
Ignition key hole illumination
: 12V - 0.8W
PKIB2172E
INTERIOR ROOM LAMP
LT-217
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
Removal and Installation
NKS001RO
MAP LAMP
Removal
1.
Pull wider part of thin plate of the map lamp to disengage the
metal clip.
2.
Pull map lamp in direction shown by the arrow in the figure.
3.
Disconnect map lamp connector and remove the map lamp.
Installation
Installation is the reverse order of removal.
PERSONAL LAMP
Removal
1.
Insert a clip driver or suitable tool and disengage the metal clip
fittings of the personal lamp.
2.
Disconnect personal lamp connector and remove the personal
lamp.
Installation
installation is the reverse order of removal.
ROOM LAMP
Removal
1.
Remove the lens using clip driver or suitable tool.
2.
Using a clip driver or suitable tool and disengage the metal clip
fittings of the room lamp.
3.
Disconnect room lamp connector and remove the room lamp.
Installation
Installation is the reverse order of removal.
PKIA2520E
PKIA2540E
PKIA2539E
LT-218
INTERIOR ROOM LAMP
Revision: 2006 August
2006 Murano
STEP LAMP
Removal
1.
Insert a screwdriver in the chink between lens and door trim,
and remove the lens.
2.
Using a clip driver or a suitable tool, press and disengage the
metal clip fittings of the step lamp.
3.
Disconnect the step lamp connector and remove the step lamp.
Installation
Installation is the reverse order of removal.
LUGGAGE ROOM LAMP
Removal
1.
Insert a screwdriver as shown in the figure and pull out the lug-
gage room lamp.
2.
Disconnect the luggage room lamp connector and remove lug-
gage room lamp.
Installation
Installation is the reverse order of removal.
PKIB2175E
PKIA2514E
PKIA2541E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст