Nissan Murano Z50 (2006 year). Manual — part 170
ILLUMINATION
LT-219
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
ILLUMINATION
PFP:27545
System Description
NKS001RP
●
BCM (Body Control Module) controls illumination lamp operation.
●
IPDM E/R (Intelligent Power Distribution Module Engine Room) operates illumination lamps according to
CAN communication signals from BCM.
OUTLINE
Power is supplied at all times
●
to ignition relay located in IPDM E/R, from battery direct,
●
through 10A fuse (No. 71, located in IPDM E/R)
●
to tail lamp relay located in IPDM E/R and
●
to CPU (central processing unit) located in IPDM E/R,
●
through 15A fuse (No. 78, located in IPDM E/R)
●
to CPU located in IPDM E/R,
●
through 50A fusible link (letter F, located in fuse and fusible link block)
●
to BCM terminal 55,
●
through 10A fuse [No. 18, located in fuse block (J/B)]
●
to BCM terminal 42,
●
through 10A fuse [No. 21, located in fuse block (J/B)]
●
to combination meter terminal 21.
With the ignition switch in the ON or START position, power is supplied
●
to ignition relay, located in IPDM E/R,
●
through 10A fuse [No. 1, located in fuse block (J/B)]
●
to BCM terminal 38,
●
through 10A fuse [No. 14, located in fuse block (J/B)]
●
to combination meter terminal 20.
With the ignition switch in the ACC or ON position, power is supplied
●
through 10A fuse [No. 6, located in fuse block (J/B)]
●
to BCM terminal 11.
Ground is supplied
●
to BCM terminal 52
●
through grounds M14 and M78,
●
to IPDM E/R terminals 38 and 60
●
through grounds E13, E26 and E28,
●
to combination meter 22, 23 and 24
●
through grounds M14 and M78.
ILLUMINATION LAMP OPERATION
When the lighting switch is in 1ST position, BCM detects the LIGHTING SWITCH 1ST POSITION (ON) by
BCM combination switch reading function. And then, BCM sends position light request signal (ON) through
CAN communication.
When receiving position light request signal (ON), IPDM E/R turns ON tail lamp relay in IPDM E/R. And then
supplies power
●
through IPDM E/R terminal 22
●
to CVT illumination terminal 1
●
to VDC off switch (illumination) terminal 3 (with VDC)
●
to headlamp aiming switch (illumination) terminal 3 (with headlamp aiming)
●
to AWD lock switch (illumination) terminal 4 (AWD models)
●
to heated seat switch (driver side) (illumination) terminal 5 (with heater seat)
●
to heated seat switch (passenger side) (illumination) terminal 5 (with heater seat)
●
to door mirror remote control switch (illumination) terminal 16
LT-220
ILLUMINATION
Revision: 2006 August
2006 Murano
●
to combination switch (spiral cable) terminal 26
●
to A/C and AV switch terminal 3
●
to NAVI control unit (illumination) terminal 61 (with NAVI)
●
to coin box illumination terminal 1 and
●
to glove box lamp terminal 1.
Ground is supplied
●
to CVT illumination terminal 2
●
to VDC off switch (illumination) terminal 4 (with VDC)
●
to headlamp aiming switch (illumination) terminal 4 (with headlamp aiming)
●
to AWD lock switch (illumination) terminal 2 (AWD models)
●
to heated seat switch (driver side) (illumination) terminal 6 (with heater seat)
●
to heated seat switch (passenger side) (illumination) terminal 6 (with heater seat)
●
to door mirror remote control switch (illumination) terminal 15
●
to combination switch (spiral cable) terminal 27 and
●
to A/C and AV switch terminal 4
●
through combination meter terminal 15,
●
to NAVI control unit (illumination) terminal 1
●
to coin box illumination terminal 2 and
●
to glove box lamp terminal 2
●
through grounds M14 and M78.
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 1ST or 2ND position (or if auto light system is acti-
vated), and the ignition switch is turned from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the illumination lamps remain illuminated for 5 minutes, and then the illumination lamps
are turned off.
When the lighting switch is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after
illumination lamps are turned off by the battery saver control, and illumination lamps illuminate again.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
CAN Communication System Description
NKS001RQ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Unit
NKS001RR
Refer to
ILLUMINATION
LT-221
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
Schematic
NKS001RS
TKWB2594E
LT-222
ILLUMINATION
Revision: 2006 August
2006 Murano
Wiring Diagram — ILL —
NKS001RT
TKWB2595E
ILLUMINATION
LT-223
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
TKWB2596E
LT-224
ILLUMINATION
Revision: 2006 August
2006 Murano
TKWB2597E
ILLUMINATION
LT-225
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
TKWB2808E
LT-226
ILLUMINATION
Revision: 2006 August
2006 Murano
TKWB2598E
ILLUMINATION
LT-227
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
TKWB2599E
LT-228
ILLUMINATION
Revision: 2006 August
2006 Murano
Removal and Installation
NKS001RU
ILLUMINATION CONTROL SWITCH
1.
Remove the meter lid. Refer to
DI-24, "Disassembly and Assem-
.
2.
Remove the illumination control switch fixing screws and
remove the unit from the meter lid.
CONSOLE POCKET LAMP
1.
Remove the instrument stay cover. Refer to
.
2.
Turn the bulb socket counterclockwise and unlock it.
GLOVE BOX LAMP
1.
Remove the instrument passenger lower panel. Refer to
.
2.
Turn the bulb socket counterclockwise and unlock it.
COIN BOX ILLUMINATION
1.
Remove the A/T console finisher. Refer to
2.
Turn the bulb socket counterclockwise and unlock it.
PKIA2543E
Console pocket lamp
: 12V - 1.4W
PKIA2544E
Glove box lamp
: 12V - 1.4W
PKIB2183E
Coin box illumination
: 12V - 1.4W
PKIA2947E
BULB SPECIFICATIONS
LT-229
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: 2006 August
2006 Murano
BULB SPECIFICATIONS
PFP:26297
Headlamp
NKS001RV
Exterior Lamp
NKS001RW
Interior Lamp/Illumination
NKS001RX
Item
Wattage (W)
High/Low (Halogen type)
65/55 (HB5)
High/Low (Xenon type)
35 (D2S)
Item
Wattage (W)
Front combination lamp
Front turn signal lamp
21 (amber)
Parking lamp
3.8
Front side marker lamp
3.8
Rear combination lamp
Stop/Tail/Rear turn signal lamp
LED
Rear side marker lamp
LED
Front fog lamp
51 (HB4)
Back-up lamp
16
License plate lamp
5
High-mounted stop lamp (back door mount)
LED
Item
Wattage (W)
Map lamp
8
Room lamp
8
Personal lamp
8
Luggage room lamp
8
Step lamp
2.7
Glove box lamp
1.4
Vanity mirror lamp
2
Ignition key hole illumination
0.8
Console pocket lamp
1.4
Coin box illumination
1.4
LT-230
BULB SPECIFICATIONS
Revision: 2006 August
2006 Murano
LU-1
ENGINE LUBRICATION SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
LU
Revision: 2006 August
2006 Murano
ENGINE LUBRICATION SYSTEM
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Precautions for Liquid Gasket . . . . . . . . .. 2
LIQUID GASKET APPLICATION PROCEDURE
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 3
LUBRICATION SYSTEM . . . . . . . . . . . 4
Lubrication Circuit . . . . . . . . . . . . . 4
System Chart . . . . . . . . . . . . . . ... 5
ENGINE OIL . . . . . . . . . . . . . . . ... 6
Inspection . . . . . . . . . . . . . . . . . 6
Changing Engine Oil . . . . . . . . . . . . 8
OIL FILTER . . . . . . . . . . . . . . . . . 9
Removal and Installation . . . . . . . . . . .. 9
OIL COOLER . . . . . . . . . . . . . . . 10
Removal and Installation . . . . . . . . . . 10
OIL PUMP . . . . . . . . . . . . . . . . . 12
Removal and Installation . . . . . . . . . . 12
Disassembly and Assembly . . . . . . . . . 12
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 15
LU-2
PRECAUTIONS
Revision: 2006 August
2006 Murano
PRECAUTIONS
PFP:00001
Precautions for Liquid Gasket
NBS002A1
LIQUID GASKET APPLICATION PROCEDURE
1.
Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.
●
Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt
holes.
2.
Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.
3.
Apply liquid gasket to the liquid gasket application surface.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
.
●
Within 5 minutes of liquid gasket application, install the mating component.
●
If liquid gasket protrudes, wipe it off immediately.
●
Do not retighten mounting bolts or nuts after the installation.
●
After 30 minutes or more have passed from the installation, fill engine oil and engine coolant.
PREPARATION
LU-3
C
D
E
F
G
H
I
J
K
L
M
A
LU
Revision: 2006 August
2006 Murano
PREPARATION
PFP:00002
Special Service Tools
NBS002A2
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
NBS002A3
Tool number
(Kent-Moore No.)
Tool name
Description
ST25051001
(J25695-1)
Oil pressure gauge
Measuring oil pressure
Maximum measuring range: 2,452 kPa (25
kg/cm
2
, 356 psi)
ST25052000
(J25695-2)
Hose
Adapting oil pressure gauge to oil pan (upper)
KV10115801
(J38956)
Oil filter wrench
Removing oil filter
a: 64.3 mm (2.531 in)
NT050
S-NT559
S-NT375
Tool name
Description
Power tools
Loosening nuts and bolts
Deep socket
Removing and installing oil pressure switch
a: 27 mm (1.06 in)
PBIC0190E
PBIC4066E
LU-4
LUBRICATION SYSTEM
Revision: 2006 August
2006 Murano
LUBRICATION SYSTEM
PFP:15010
Lubrication Circuit
NBS002A4
PBIC2688E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст