Nissan Frontier. Manual — part 1316
WT-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010212547
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
CONSULT Function (BCM - AIR PRESSURE MONITOR)
INFOID:0000000010212548
NOTE:
Direct Diagnostic Mode
Description
ECU Identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
ECU Id
en
tif
ica
tio
n
Sel
f Di
agn
os
tic Re
su
lt
Dat
a
M
on
ito
r
Acti
ve
T
est
W
ork
su
pp
ort
Co
nf
ig
ur
at
io
n
CAN Diag S
upport Mntr
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
Air conditioner
AIR CONDITIONER
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
Panic alarm system
PANIC ALARM
×
DIAGNOSIS SYSTEM (BCM)
WT-13
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
SELF DIAGNOSTIC RESULT
NOTE:
Before performing Self Diagnostic Result, be sure to register the ID, or else the actual malfunction may be dif-
ferent from that displayed on CONSULT.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Self-Diagnosis (Without CONSULT)
INFOID:0000000009480248
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
SELF DIAGNOSTIC PROCEDURE (WITHOUT CONSULT)
Monitor Item
Condition
Specification
VEHICLE SPEED
Drive vehicle.
Vehicle speed (km/h or mph).
AIR PRESS FL
• Drive vehicle for a few minutes.
or
• Ignition switch ON and activation tool is trans-
mitting activation signals.
Tire pressure (kPa, kg/cm
2
or psi).
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
ID REGST FL1
Ignition switch ON.
Registration ID: Green.
No registration: Red.
ID REGST FR1
ID REGST RR1
ID REGST RL1
WARNING LAMP
Ignition switch ON.
Low tire pressure warning lamp on: ON.
Low tire pressure warning lamp off: OFF.
BUZZER
Ignition switch ON.
Buzzer in combination meter on: ON.
Buzzer in combination meter off: OFF.
Test Item
Description
WARNING LAMP
This test is able to check tire pressure warning lamp operation [Off/On].
ID REGIST WARNING
This test is able to check ID regist warning chime operation [Off/On].
FLAT TIRE WARNING
This test is able to check flat tire warning chime operation [Off/On].
HORN
This test is able to check horn operation [On].
FLASHER
This test is able to check turn signal lamp operation [Off/LH/RH].
Support Item
Description
ID REGIST
Refer to
ID READ
The registered ID number is displayed.
WT-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
1. Turn ignition switch ON.
2. Ground the tire pressure warning check connector to initiate self diagnosis.
3. Compare the flashing pattern with the flash code chart below.
NOTE:
The system is normal when the low tire pressure warning lamp flashes 5 times and continues repeating. Self-
diagnosis results are erased automatically by turning the ignition switch “OFF”.
Flash Code
Malfunction part
Reference
page
15
16
17
18
Tire pressure dropped below specified value. Refer to
—
21
22
23
24
Transmitter no data (FL)
Transmitter no data (FR)
Transmitter no data (RR)
Transmitter no data (RL)
31
32
33
34
Transmitter checksum error (FL)
Transmitter checksum error (FR)
Transmitter checksum error (RR)
Transmitter checksum error (RL)
35
36
37
38
Transmitter pressure data error (FL)
Transmitter pressure data error (FR)
Transmitter pressure data error (RR)
Transmitter pressure data error (RL)
41
42
43
44
Transmitter function code error (FL)
Transmitter function code error (FR)
Transmitter function code error (RR)
Transmitter function code error (RL)
45
46
47
48
Transmitter battery voltage low (FL)
Transmitter battery voltage low (FR)
Transmitter battery voltage low (RR)
Transmitter battery voltage low (RL)
52
Vehicle speed signal
54
Vehicle ignition signal
ALEIA0050GB
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
WT-15
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DTC/CIRCUIT DIAGNOSIS
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
INFOID:0000000009480249
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
INFOID:0000000009480250
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. Refer to
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT within 5 minutes.
Does DATA MONITOR ITEM display tire pressure as normal without any warning lamp?
YES
>> Inspection End.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009480251
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.
CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT.
Are all tire pressures displayed as 0 kPa?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES
>> Repair or replace tire pressure receiver connector.
DTC
CONSULT
DTC detecting condition
C1708
[NO - DATA] - FL
Data from FL transmitter cannot be received.
C1709
[NO - DATA] - FR
Data from FR transmitter cannot be received.
C1710
[NO - DATA] - RR
Data from RR transmitter cannot be received.
C1711
[NO - DATA] - RL
Data from RL transmitter cannot be received.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст