Nissan Frontier. Manual — part 850
FRONT DOOR GLASS AND REGULATOR
GW-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
3. Temporarily reconnect the power window switch (if equipped).
4. For power windows, operate the power window switch to raise/
lower the door window until the glass bolts can be seen.
5. For manual windows, temporarily reinstall the window crank
handle and lower the window until the glass bolts can be seen.
6. Remove the glass bolts.
7. Raise the front door glass and hold it in place with suitable tool
(A).
8. Disconnect the harness connector from the regulator assembly
(if equipped).
9. Remove the bolts and the regulator assembly.
NOTE:
Power window shown, manual window similar.
LIIA1686E
PIIB3510J
Front
WIIA1033E
GW-18
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
DISASSEMBLY AND ASSEMBLY
Remove the regulator motor or manual crank assembly from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
INSTALLATION
1. Install the regulator assembly.
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor or
crank assembly to install the assembly in the door.
b. Install the top front regulator bolt.
c.
Install the bottom front regulator bolt.
d. Install the bottom rear regulator bolt.
e. Tighten the top rear regulator bolt.
f.
Install the top window motor or manual crank assembly bolt.
g. Install the lower window motor or manual crank assembly bolt
h. Install the rear window motor or manual crank assembly bolt.
2. Connect the harness connector (if equipped) to the regulator assembly.
Front
Regulator and motor or
manual crank assembly
bolts
: 5.1 N·m (0.52 kg-m, 45 in-lb)
WIIA1033E
FRONT DOOR GLASS AND REGULATOR
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
3. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten glass bolts.
4. Check the glass for proper fit. Refer to
.
5. Reposition the vapor barrier.
6. Install front door finisher. Refer to
INT-15, "Removal and Installation"
.
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1686E
GW-20
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
REAR DOOR GLASS AND REGULATOR
Rear Door Glass
INFOID:0000000009478977
REMOVAL
1. Remove the rear door finisher. Refer to
INT-15, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Remove the inside seal.
4. Temporarily reconnect the power window switch (if equipped).
5. Remove the glass run from the partition glass.
6. For power windows, operate the power window switch to raise/
lower the door window until the glass bolts can be seen.
7. For manual windows, temporarily reinstall the window crank
handle and lower the window until the glass bolts can be seen.
8. Remove the partition sash bolt (lower) and screw (upper) to
remove the sash.
9. Remove the bolts and the glass.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass alignment. Follow the FITTING INSPECTION procedure.
FITTING INSPECTION
• Check that the glass fits securely into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass carrier plate bolts to adjust the glass position.
Rear Door Glass Regulator
INFOID:0000000009478978
REMOVAL
1. Remove the rear door finisher. Refer to
INT-15, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Remove the inside seal.
4. Temporarily reconnect the power window switch (if equipped).
LIIA1689E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
Regulator and motor
or manual crank as-
sembly bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст