Nissan Frontier. Manual — part 851
REAR DOOR GLASS AND REGULATOR
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
5. For power windows, operate the power window switch to raise/
lower the door window until the glass bolts can be seen.
6. For manual windows, temporarily reinstall the window crank
handle and lower the window until the glass bolts can be seen.
7. Raise the rear door glass and hold it in place with suitable tool
(A).
8. Remove the bolts and the regulator assembly.
• Disconnect the harness connector (if equipped) from the regu-
lator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Gear wear
• Regulator deformation
• Spring damage
• Grease condition for each sliding part
LIIA1689E
PIIB3511J
Front
WIIA1034E
GW-22
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
INSTALLATION
1. Connect the harness connector and install the regulator assembly.
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor or
manual crank assembly to install the assembly in the door.
b. Install the top front regulator bolt.
c.
Install the bottom regulator bolt.
d. Tighten the top rear regulator bolt.
e. Install the top window motor or manual crank assembly bolt.
f.
Install the lower window motor or manual crank assembly bolt.
g. Install the front window motor or manual crank assembly bolt.
2. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten glass bolts.
3. Install the partition sash
4. Check the glass alignment. Refer to
.
Front
Regulator and motor or
manual crank assembly
bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
WIIA1034E
LIIA1689E
REAR DOOR GLASS AND REGULATOR
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
5. Install the inside seal.
6. Reposition the vapor barrier.
7. Install the rear door finisher. Refer to
GW-24
< REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
SIDE WINDOW GLASS
Removal and Installation
INFOID:0000000009478979
REMOVAL
1. Remove the rear door finisher. Refer to
INT-15, "Removal and Installation"
.
2. Remove the side window glass using piano wire or power cut-
ting tool and an inflatable pump bag.
• Apply protective tape around the side window glass to protect
the painted surface from damage.
• If the window glass is to be reused, mark the body and the
glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety
glasses and heavy gloves to help prevent glass splinters
from entering your eyes or cutting your hands.
CAUTION:
• When the side window glass is to be reused, do not use a
cutting knife or power cutting tool.
• Be careful not to scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
Installation is in the reverse order of removal.
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• Check gap along bottom to confirm that glass does not contact sheet metal.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
1.
Side window glass
A.
12.0 mm (0.47 in)
B.
8.0 mm (0.31 in)
AWKIA1736ZZ
SBF034B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст