Nissan Frontier. Manual — part 1215
AIR BREATHER HOSE
TM-71
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009480447
COMPONENTS
REMOVAL
1. Disconnect air breather hose from breather tube and transmission harness connector.
2. Disconnect air breather hose from the bracket.
3. Remove the bracket bolt and remove the bracket from the transmission housing, if necessary.
4. Remove the breather tube bolt and the breather tube.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Make sure there are no pinched or blocked areas on the air breather hose after installation.
• When inserting the air breather hose, be sure to insert it fully until its end reaches the end of the tube
radius.
• Install the air breather hose with the paint mark side up.
1.
Water outlet
2.
Bracket
3.
Air breather hose
4.
Breather tube
LCIA0392E
TM-72
< UNIT REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Removal and Installation from Vehicle (For 2WD Models)
INFOID:0000000009480448
COMPONENTS
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Transmission assembly
2.
Crossmember
3.
Insulator
AWDIA0687GB
TRANSMISSION ASSEMBLY
TM-73
< UNIT REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL
1. Disconnect the battery cable from the negative terminal. Refer to
PG-83, "Removal and Installation"
2. Remove the shift selector assembly. Refer to
TM-69, "Removal and Installation"
.
3. Remove the LH fender protector. Refer to
EXT-27, "Removal and Installation of Front Fender Protector"
4. Remove the crankshaft position sensor (POS) from M/T assem-
bly.
CAUTION:
Do not damage the sensor edge.
5. Remove the under cover(s) using power tool.
6. Remove the front crossmember using power tool.
7. Remove the starter motor. Refer to
.
8. Remove the rear propeller shaft. Refer to
DLN-163, "Removal and Installation"
(3S1330),
DLN-174, "Removal and Installation"
2BJ100).
9. Remove the left and right front exhaust tubes. Refer to
.
10. Remove the clutch operating cylinder from the transmission. Refer to
CL-16, "6M/T : Removal and Instal-
.
11. Support the transmission using a suitable jack.
12. Remove the nuts securing the insulator to the crossmember.
13. Remove the crossmember using power tool.
WARNING:
Support the transmission using suitable jack.
14. Tilt the transmission slightly to gain clearance between the body and the transmission, then disconnect
the air breather hoses. Refer to
TM-71, "Removal and Installation"
15. Disconnect the following:
• Back-up lamp switch harness connector
• Park/neutral position (PNP) switch harness connector
16. Remove the harness from the retainers.
17. Remove the transmission to engine bolts using power tool.
18. Separate the transmission from the engine and remove it from the vehicle.
WARNING:
Support the transmission while removing it using suitable jack.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the transmission to the engine, tighten the bolts to
the specified torque.
CAUTION:
• When installing be careful to avoid interference between
transmission main drive gear and clutch cover.
• After installation, check for oil leakage and oil level. Refer to
.
• If flywheel is removed, align dowel pin with the smallest hole of flywheel.
• When replacing an engine or transmission you must make sure the dowels are installed correctly
during re-assembly.
• Improper alignment caused by missing dowels may cause vibration, oil leaks or breakage of drive
train components.
LCIA0367E
Quantity
10
Bolt length “ ”
mm (in)
65 (2.56)
Tightening torque
N·m (kg-m, ft-lb)
75 (7.7, 55)
WCIA0507E
TM-74
< UNIT REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
Removal and Installation from Vehicle (For 4WD Models)
INFOID:0000000009480449
COMPONENTS
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Disconnect the battery cable from the negative terminal. Refer to
PG-83, "Removal and Installation"
2. Remove the shift selector assembly. Refer to
TM-69, "Removal and Installation"
.
1.
Transmission assembly
2.
Crossmember
3.
Insulator
WCIA0577E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст