Nissan Frontier. Manual — part 1271

CONTROL VALVE WITH TCM

TM-295

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

15. Install snap ring to A/T assembly harness connector.
16. Connect A/T assembly harness connector.
17. Connect the negative battery terminal.
18. Refill the A/T with fluid and check the fluid level and for fluid

leakage. Refer to

TM-269, "Checking the A/T Fluid (ATF)"

.

SCIA5039E

TM-296

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

REAR OIL SEAL

REAR OIL SEAL

Removal and Installation

INFOID:0000000009480682

REMOVAL

1. Remove rear propeller shaft. Refer to

DLN-143, "Removal and Installation"

(2S1330),

DLN-152, "Removal

and Installation"

(3S1310),

DLN-163, "Removal and Installation"

(3S1330),

DLN-174, "Removal and

Installation"

(3S1330-2BJ100).

2. Remove transfer from transmission (4WD models). Refer to

DLN-101, "Removal and Installation"

(TX15B).

3. Remove rear oil seal using a suitable tool.

CAUTION:

Do not scratch rear extension assembly (2WD models) or

adapter case assembly (4WD models).

INSTALLATION

1. Install new rear oil seal until it is flush into the rear extension

case (2WD models) using Tool or adapter case (4WD models)

using suitable tool.

CAUTION:

• Apply ATF to rear oil seal.

• Do not reuse rear oil seal.

2. Install transfer to transmission (4WD models). Refer to

DLN-

101, "Removal and Installation"

(TX15B).

3. Install rear propeller shaft. Refer to

DLN-143, "Removal and

Installation"

(2S1330),

DLN-152, "Removal and Installation"

(3S1310),

DLN-163, "Removal and Installation"

(3S1330),

DLN-

174, "Removal and Installation"

(3S1330-2BJ100).

4. Check the A/T fluid level and for fluid leaks. Refer to

TM-269,

"Checking the A/T Fluid (ATF)"

.

SCIA5254E

Tool number

: ST33400001 (J-26082)

WCIA0475E

KEY INTERLOCK CABLE

TM-297

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

KEY INTERLOCK CABLE

Component

INFOID:0000000009480683

CAUTION:

• Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interfer-

ence with adjacent parts.

• After installing key interlock cable to shift selector, make sure that casing cap and bracket are firmly

secured in their positions. If casing cap can be removed with an external load of less than 39 N (4.0

kg, 8.8 lb), replace key interlock cable with new one.

Removal and Installation

INFOID:0000000009480684

REMOVAL

1. Remove the A/T finisher. Refer to

IP-29, "Exploded View"

.

2. Remove the lower glove box. Refer to

IP-23, "Removal and Installation"

.

3. Remove instrument lower panel LH. Refer to

IP-18, "Removal and Installation"

.

WCIA0467E

TM-298

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

KEY INTERLOCK CABLE

4. Unlock slider from adjuster holder by squeezing lock tabs.
5. Remove casing cap from bracket of shift selector assembly and

remove interlock rod from adjuster holder.

6. Remove holder from key cylinder and remove key interlock

cable.

INSTALLATION

1. Set key interlock cable to key cylinder and install holder.
2. Set shift selector handle to “P” position.
3. Turn ignition key to "LOCK" position.

SCIA1230E

LCIA0375E

SCIA2258E