Qashqai J11. Mirrors — part 4
MIR-50
< WIRING DIAGRAM >
AUTO ANTI-DAZZLING MIRROR SYSTEM
AUTO ANTI-DAZZLING MIRROR SYSTEM
Wiring Diagram
INFOID:0000000010502665
JRLWE4139GB
AUTO ANTI-DAZZLING MIRROR SYSTEM
MIR-51
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
JRLWE4140GB
MIR-52
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000011378312
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much malfunction information (conditions and environment when the mal-
function occurred) as possible when the customer brings the vehicle in.
>> GO TO 2.
2.
REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 2. Then identify where to start the diag-
nosis based on possible causes and symptoms.
>> GO TO 4.
4.
IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system.
>> GO TO 5.
5.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Is the malfunctioning part repaired or replaced?
YES
>> Trouble diagnosis is completed.
NO
>> GO TO 3.
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
MIR-53
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
Component Inspection
INFOID:0000000011405231
1.
CHECK MIRROR SWITCH & CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch.
Door mirror remote control switch
condition
Continuity
Terminal
Change over
switch
Mirror switch
Driver side (RHD models)
Passenger side (LHD models)
15
11
RIGHT
RIGHT
Existed
10
9
15
9
LEFT
10
11
15
3
UP
10
11
15
11
DOWN
10
3
Driver side (LHD models)
Passenger side (RHD models)
15
12
LEFT
RIGHT
10
1
15
1
LEFT
10
12
15
4
UP
10
12
15
12
DOWN
10
4
MIR-54
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR (OPEN/CLOSE MOTOR)
DOOR MIRROR (OPEN/CLOSE MOTOR)
Component Function Check
INFOID:0000000011405232
1.
CHECK DOOR MIRROR RETRACT FUNCTION
1.
Turn ignition switch ON.
2.
Operate open/close switch. Check that door mirror operates normally.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000011405233
1.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 10 A fuse (#14)
• Harness for open or short between door mirror remote control switch harness connector and battery termi-
nal.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK DOOR MIRROR OPEN RELAY AND DOOR MIRROR CLOSE RELAY INPUT SIGNAL
1.
Connect door mirror remote control switch connector.
2.
Disconnect door mirror open relay and door mirror close relay connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror open relay and door mirror close relay harness connector and ground.
(+)
(
−
)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
15
Ground
Battery voltage
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
10
Existed
DOOR MIRROR (OPEN/CLOSE MOTOR)
MIR-55
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK HARNESS CONTINUITY-1
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch harness connector and door mirror open/
close relay harness connector.
4.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace harness.
6.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Connect door mirror open relay and door mirror close relay connector.
3.
Disconnect door mirror (driver side) connector and door mirror (passenger side) connector.
4.
Turn ignition switch ON.
5.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror open/close relay
Connector
Terminal
M100
4
Ground
Door mirror remote
control switch
(open/close switch)
Auto
12
Other than above
0
M101
Close
12
Other than above
0
door mirror remote control switch
Door mirror open/close relay
Continuity
Connector
Terminal
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
5
M100
4
Existed
7
M101
door mirror remote control switch
Ground
Continuity
Connector
Terminal
Not existed
D6 (LHD models)
D36 (RHD models)
5
7
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror
Connector
Terminal
D27 (LHD models)
D16 (RHD models)
3
Ground
Door mirror remote
control switch
(open/close switch)
Auto
12
Close
0
11
Auto
0
Close
12
D3 (LHD models)
D40 (RHD models)
3
Auto
12
Close
0
11
Auto
0
Close
12
MIR-56
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR (OPEN/CLOSE MOTOR)
YES
>> GO TO 8.
NO
>> GO TO 7.
7.
CHECK HARNESS CONTINUITY-2
1.
Turn ignition switch OFF.
2.
Disconnect door mirror open relay connector and door mirror close relay connector.
3.
Check continuity between door mirror harness connector and door mirror open relay and door mirror close
relay harness connector.
4.
Check continuity between door mirror harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK DOOR MIRROR OPEN RELAY
Check door mirror open relay.
Refer to
MIR-57, "Component Inspection (Door Mirror Open Relay)"
.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace door mirror open relay.
9.
CHECK DOOR MIRROR CLOSE RELAY
Check door mirror close relay.
Refer to
MIR-57, "Component Inspection (Door Mirror Close Relay)"
.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace door mirror close relay.
10.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH
Check door mirror remote control switch (open/close switch).
Refer to
MIR-57, "Component Inspection (Door Mirror Remote Control Switch)"
.
Is the inspection result normal?
YES
>> Replace door mirror open/close motor.
NO
>> Replace door mirror remote control switch.
11.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
door mirror
Door mirror open/close relay
Continuity
Connector
Terminal
Connector
Terminal
D27 (LHD models)
D16 (RHD models)
3
M100
3
Existed
11
M101
D3 (LHD models)
D40 (RHD models)
3
M100
11
M101
door mirror
Ground
Continuity
Connector
Terminal
Not existed
D27 (LHD models)
D16 (RHD models)
3
11
D3 (LHD models)
D40 (RHD models)
3
11
DOOR MIRROR (OPEN/CLOSE MOTOR)
MIR-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Component Inspection (Door Mirror Remote Control Switch)
INFOID:0000000011405234
1.
CHECK OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch.
Component Inspection (Door Mirror Open Relay)
INFOID:0000000011405235
1.
CHECK DOOR MIRROR OPEN RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror open relay.
3.
Check the continuity between door mirror open relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror open relay.
Component Inspection (Door Mirror Close Relay)
INFOID:0000000011405236
1.
CHECK DOOR MIRROR OPEN/CLOSE RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror close relay.
3.
Check the continuity between door mirror close relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
Door mirror remote control switch
Condition
Continuity
Terminal
15
5
Open/close switch
AUTO
Existed
10
7
15
7
CLOSE
10
5
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
MIR-58
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR (OPEN/CLOSE MOTOR)
NO
>> Replace door mirror close relay.
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
MIR-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
Component Function Check
INFOID:0000000011405237
1.
CHECK FUNCTION
1.
Turn the door mirror open/close switch to “AUTO”.
2.
Turn ignition switch ON.
3.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
4.
Select “RETRACTABLE MIRROR” in “ACTIVE TEST” mode.
5.
Touch “On” check that it works normally.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000011405238
1.
CHECK DOOR MIRROR OPEN RELAY AND DOOR MIRROR CLOSE RELAY POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror open relay and door mirror close relay connector.
3.
Check voltage between door mirror open relay and door mirror close relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 10 A fuse (#28)
• Harness for open or short between door mirror remote control switch harness connector and battery termi-
nal.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK BCM INPUT SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between door mirror open relay and door mirror close relay harness connector and BCM
harness connector.
3.
Check continuity between BCM harness connector and ground.
(+)
(
−
)
Voltage (V)
(Approx.)
Door mirror open/close relay
Connector
Terminal
M100
1
Ground
Battery voltage
M101
1
5
Door mirror open/close relay
BCM
Continuity
Connector
Terminal
Connector
Terminal
M100
2
M70
58
Existed
M101
BCM
Ground
Continuity
Connector
Terminal
M70
58
Not existed
MIR-60
< DTC/CIRCUIT DIAGNOSIS >
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK OPEN/CLOSE MOTOR GROUND CIRCUIT
1.
Disconnect door mirror remote control switch connector.
2.
Check continuity between door mirror remote control switch harness connector and door mirror open relay
harness connector.
3.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK DOOR MIRROR OPEN RELAY
Check door mirror open relay.
Refer to
MIR-61, "Component Inspection (Door Mirror Open Relay)"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness or connector.
6.
CHECK DOOR MIRROR CLOSE RELAY
Check door mirror close relay.
Refer to
MIR-61, "Component Inspection (Door Mirror Close Relay)"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness or connector.
7.
CHECK BCM FUNCTION
1.
Turn the door mirror open/close switch to AUTO.
2.
Connect door mirror remote control switch connector, door mirror open relay, door mirror close relay and
BCM connector.
3.
Turn ignition switch ON.
4.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
5.
Select “RETRACTABLE MIRROR” in “ACTIVE TEST” mode.
6.
Touch “On” and check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
door mirror remote control switch
Door mirror open relay
Continuity
Connector
Terminal
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
7
M100
5
Existed
door mirror remote control switch
Ground
Continuity
Connector
Terminal
D6 (LHD models)
D36 (RHD models)
7
Not existed
(+)
(
−
)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M70
58
Ground
RETRACTABLE
MIRROR
ON
0
OFF
Battery voltage
AUTO RETRACTABLE DOOR MIRROR CIRCUIT
MIR-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
8.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection (Door Mirror Open Relay)
INFOID:0000000011405239
1.
CHECK DOOR MIRROR OPEN RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror open relay.
3.
Check the continuity between door mirror open relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror open relay.
Component Inspection (Door Mirror Close Relay)
INFOID:0000000011405240
1.
CHECK DOOR MIRROR OPEN/CLOSE RELAY
1.
Turn ignition switch OFF.
2.
Remove door mirror close relay.
3.
Check the continuity between door mirror close relay terminals
under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror close relay.
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
Terminal
Condition
Continuity
4
3
No current supply
Existed
12 V direct current supply between ter-
minals 1 and 2.
Not existed
5
12 V direct current supply between ter-
minals 1 and 2.
Existed
No current supply
Not existed
JMLIA0997ZZ
MIR-62
< SYMPTOM DIAGNOSIS >
ELECTRIC FOLDABLE DOOR MIRROR DOES NOT OPERATE
SYMPTOM DIAGNOSIS
ELECTRIC FOLDABLE DOOR MIRROR DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000011378323
1.
CHECK DOOR MIRROR (OPEN/CLOSE MOTOR) CIRCUIT
Check door mirror (open/close motor) circuit.
Refer to
MIR-54, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
AUTO RETRACTABLE DOOR MIRROR DOES NOT OPERATE
MIR-63
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
AUTO RETRACTABLE DOOR MIRROR DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000011378324
1.
CHECK INTELLIGENT KEY AND DOOR REQUEST SWITCH OPERATION
Check operation of Intelligent Key and door request switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR MIRROR (OPEN/CLOSE MOTOR) CIRCUIT
Check door mirror (open/close motor) circuit.
Refer to
MIR-54, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK AUTO RETRACTABLE DOOR MIRROR CIRCUIT
Check auto retractable door mirror circuit.
Refer to
MIR-59, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> GO TO 1.
MIR-64
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work Flow
INFOID:0000000011378325
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of
the customer's comments; refer to
MIR-68, "Diagnostic Worksheet"
. This information is necessary to duplicate
the conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain
all the facts and conditions that exist when the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer is
concerned about. This can be accomplished by a test drive with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
• Squeak – (Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces
= higher pitch noise/softer surfaces = lower pitch noises/edge to surface = chirping
• Creak – (Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch depen-
dent on materials/often brought on by activity.
• Rattle – (Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
• Knock – (Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
• Tick – (Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
• Thump – (Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
• Buzz – (Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
• Often the degree of acceptable noise level will vary depending upon the person. A noise that a technician
may judge as acceptable may be very irritating to the customer.
• Weather conditions, especially humidity and temperature, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when the repair is reconfirmed.
SBT842
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-65
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T model, drive position on A/T model).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.
• Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.
• If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1.
Narrow down the noise to a general area. To help pinpoint the source of the noise, use a listening tool
(Engine Ear or mechanics stethoscope).
2.
Narrow down the noise to a more specific area and identify the cause of the noise by:
• Removing the components in the area that is are suspected to be the cause of the noise.
Do not use too much force when removing clips and fasteners, otherwise clips and fastener can be broken
or lost during the repair, resulting in the creation of new noise.
• Tapping or pushing/pulling the component that is are suspected to be the cause of the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only tem-
porarily.
• Feeling for a vibration by hand by touching the component(s) that is are suspected to be the cause of the
noise.
• Placing a piece of paper between components that is are suspected to be the cause of the noise.
• Looking for loose components and contact marks.
MIR-66, "Inspection Procedure"
REPAIR THE CAUSE
• If the cause is a loose component, tighten the component securely.
• If the cause is insufficient clearance between components:
- Separate components by repositioning or loosening and retightening the component, if possible.
- Insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. These insulators are available through the authorized Nissan Parts Department.
CAUTION:
Never use excessive force as many components are constructed of plastic and may be damaged.
NOTE:
• URETHANE PADS
Insulates connectors, harness, etc.
• INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
• INSULATOR (Light foam block)
• FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
The following materials, not available through NISSAN Parts Department, can also be used to repair
squeaks and rattles.
• UHMW(TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
• SILICONE GREASE
Used in place of UHMW tape that is be visible or does not fit.
Note: Will only last a few months.
• SILICONE SPRAY
Used when grease cannot be applied.
• DUCT TAPE
Used to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст